I would like to be able to share expenses and work on my experimental aircraft now and in the future. I would like to have a partnership with several others both to build and to operate an experimental 4 to 6 place aircraft. Perhaps, especially in building, this is not advisable. I would like to...

Hello, Is this engine is #1 or #2 dynafocal mount? Thanks -- Minicab F-PRAZ Philippe Vessaire Ò¿Ó¬

http://www.theregister.co.uk/2006/01/23/flying_car/

Anyone have any info on the lanier paraplane(and the II version)? 20 mph landing speed and a 150 mph cruise seems a lot like the claims on the infomercials for kitchen gadgets. TIA Pat

Yesterday's coverage pointed out two things that caught my ear: First, that it was a considerable amount of time before the Brothers were able to duplicate the longest flight of the day, and second, that the craft was (apparently) just on the edge of being able to fly. So, anyone know what aspect...

On the new Cessna 172's, Cessna uses a Black mat type carpeting in the front, then it goes to actual carpet in the back. I'm looking for a source for the black mat in the front to do the floor in a Mooney. Anyone know what they use or where I might get some? I believe it's a polypropylene type...

Aircraft tire and tube, New, 500 x 5 Low starting bid of just $35.00 or Buy it Now for only $50.00. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&viewitem=&rd=1,1&item=4609915168&sspagename=STRK%3AMESE%3AIT

Folks - I'd like to remove my plugs and see how they look. Externally, they look like they may be rusted in place - don't know for sure, havn't tried to undo one. Any suggestions on how to approach the possibility they may be rusted in place? Lots of penetrating oil? - Mike

For those of you who may find a need for this (which probably won't be too many of you), I put my copy of a KR-20 marker beacon receiver install and op manual (with pinouts, that's why I put it up), on the site. You can download a small PDF file at http://www.bd5.com/kr-20.pdf Juan

I'm a Hatz Classic builder and for the last few months, I and other Hatz builders have been unable to access the forum on the Hatz Biplane Association web site. Out of frustration and the need to communicate with other Hatz builders, I created a Yahoo Group called Hatz_Biplane. The new Yahoo Group...

This is not aircraft related. I did some brazing on a tank and then later decided it would have been easier to have welded. I read somewhere that one should not attempt to weld over brazing. I assume becase the brazing material melts at a lower temp than the base metal, that welding over a braze...

What are the 400mA current sink superflags used for? I've got them on my Apollo equipment, but they only show hookups to older equipment.

I am interested in flying a homebuilt aeroplane from Greece to the USA and have it registered to an N number. Does anyone here have any knowledge of how hard or easy it is to do this? I have concerns like flying it from country to country in Europe, flying it to Iceland, then Canada, then...

Looking at purchasing a Rutan Defiant. Has anyone flown one and if so do you have any recommendations before I make a purchase. What did you like/not like? Would you recommend buying? Thanks Dave Culbertson

I know nothing about kitplanes/homebuilts but want to learn. If you want help or just to teach me something about it post here and i'll get your email address. I'm around CDW, private pilot, low time, etc. I don't have a garage nor the funds to start my own project any time soon which is why i'd...

I have a set of plans if you're still interested. Ric

I've added a link to Highflyer's official announcement to my Unofficial Pinckneyville FAQ. http://www.ousterhout.net/pjy-faq.html If I'm reading my webstats properly over 200 people have read the Unofficial FAQ in the past few days. Unbelievable! - John (back home again in Oregon) Ousterhout -

One of the wheels on my air compressor is at an angle. I removed it and the bolt/spindle and the inner and outer bushings wiggle. Anyone know if it is worth replacing these bushings and how to do it or should I just buy a wheel? - Mike

I am starting to plan out my panel and want to be able to have the capability of doing basic IFR operations and approaches in the future. I want to make sure I have room, in a logical location, for the equipment that will be needed. So my question- What equipment will be needed on the panel for...

I tried starting my engine today after a top overhaul, the right P-Lead got really hot and smoke came off it when I hit the starter button. where should I start looking for a short? could it be shorting back thru the starter motor?