|
|
Ventus C being parted-out by
[email protected]
My Ventus C didn't survive the last landing, the insurance company totaled it and I have the remains. I may have been the only bidder as I was able to acquire it as a salvage sale for a ridiculously low price. So, if anyone wants to offer a reasonable for the entire plane, let me know - I'll be...
|
|
4 |
4,844 |
|
|
Ventus C For Sale by
Ken Kochanski (KK)
http://sailplane-racing.org/For%20Sale/KO%20Ventus.htm
|
|
0 |
1,695 |
|
|
ventus c main wheel mudguard attachment by
Martynas Bykovas
Hello,
i plan to install mudguard on main wheel. I have mudguard itself but it is not clear how/what it should be exactly attached to.
I found wheel including mudguard drawings for cirrus however i doubt there is the same attachment principle for ventus c.
I would be grateful if someone could...
( 1 2)
|
|
16 |
786 |
|
|
Ventus C Masak Winglets by
hans
Hallo!
I'm looking for Masak Winglets for the Ventus C.
If some one wants to put the new Maughmer winglets on the Ventus and
would have a spare set of winglets left after the exchange we could be
in business too.
Best Regards
|
August 25th 06 08:11 AM
by hans
|
6 |
2,366 |
|
|
Ventus C Owners by
[email protected]
I'm a relatively new owner of N571RD, Ventus C S/N 355 and would like to know other owners to ask the occasional question. Please respond - maybe we can set up a sub-group.
|
|
3 |
214 |
|
|
Ventus C refinish, wing templates? by
Mike N.
I am thinking about doing a refinish on my Ventus C.
I am wondering if wing templates are available?
Also I'd like to cut down some of the cost by doing most of the grunt work myself. Under the watchful eye and coaching of a knowledable refinisher.
Is there anyone I can go to who would could...
|
|
4 |
270 |
|
|
Ventus C rigging by
James Hamilton
Thanks for the suggestions guys. I have four sets
of tips for the ship (plain factory tips, short factory
winglets, 16.6 extensions and Masak winglets). I rarely
ever use anything but the Masak winglets although the
problem is the same regardless of which tips I select.
The problem has always...
|
|
0 |
1,222 |
|
|
Ventus C rigging by
James Hamilton
I have a 1987 Ventus C that I purchased in 1995. Love
the plane but it wants to roll to the right at high
speeds (90kts or greater). Actually I guess it always
wants to roll to the right but I start to notice how
much left aileron pressure I have to apply to counter
the roll at the higher speeds,...
|
|
8 |
1,779 |
|
|
Ventus C Seatback Wanted by
Larry Pardue
FR, Paul Elliott of Hobbs is looking for the standard, adjustable
seatback for a Ventus C. His number is 505-397-4322 or reply to me with
the "removethis" removed, and I will send you his e-mail address.
Larry Pardue
|
|
0 |
899 |
|
|
Ventus C vs B by
tango4
Apart from the very sweet looking 17.6 m tips and tail ballast what are the
other differences between the Ventus B and the Ventus C.
Does the C have the same long cockpit as the B ?
I believe the C handles a lot better.
Ian
|
|
6 |
3,164 |
|
|
Ventus C vs LS6 by
Marshall Woodford
I’m looking for a cross county glider. The Ventus C comes with 17.5 and 15 winglets. It also has factory tips. The LS6 has low hours and the wings and horizontal stab was refinished and painted. The fuselage is in good condition and original. Both have Cobra trailers and the Ventus’s...
( 1 2)
|
|
17 |
1,058 |
|
|
Ventus C, 15m vs 17.6m by
Mike N.
Just curious, how is the performance of the Ventus C with 17.6m tips installed versus standard 15m with good winglets?
I have done some searching and seen some consensus that the 16.6m tips are typically not used much due to the performance degradation at high air speeds. But what about the 17.6...
( 1 2 3)
|
|
22 |
2,510 |
|
|
|
|
7 |
803 |
|
|
Ventus CM Manual? by
Fish
Looking for a Ventus CM flight manual.....in particular a description
of the steps required for extension and retraction of the engine, and
some description of the engine control instrument.
I've worn the internet out looking for info but have had no luck!!
Cheers
Fish
|
December 6th 05 09:13 PM
by Fish
|
2 |
1,256 |
|
|
Ventus CM starting problems by
[email protected]
For those who own Ventus Cm: have you ever measured the voltage on the starter when it is running?. Mine, with fully charged battery, while electric starter is running, voltage on battery fall out to 10volts, and on starter I measured only 6 or 6.5 volts. I have a voltage lost of aprox 2 volts over...
( 1 2 3)
|
|
28 |
691 |
|
|
Ventus cM turbulators by
Bert Willing[_2_]
I need to replace my zig-zags on the horizontal stabilizer, but I would need
to know the required position cordwise (upper and lower surface). I took it
off and cleaned before having a look at the maintainace manual - which does
not give any info on the topic... :-( Any ideas ?
Bert
TW
|
|
7 |
1,504 |
|
|
|
|
1 |
2,268 |
|
|
|
|
0 |
853 |
|
|
Ventus Ct oxygen tank mounting options by
Mike N.
Sorry for the duplicate topic post, I had an error posting the original topic.
I recently purchased a Ventus Ct that did not come with Oxygen.
There is a large pipe style clamp to the starboard side of the upper fuel tank area. As well as a small bracket forward of the with no associated mounting...
|
October 24th 19 01:59 AM
by Mike N.
|
0 |
309 |
|
|
Ventus Ct vs. CM info/data by
Andy Smielkiewicz
Hallo,
Anybody knows weight difference (empty) between those two models? How about
fuel tanks?
Thanks.
Andy
|
|
0 |
1,020 |