Does anyone know where I can get some back seats out of a Piper Lance? Im looking to take out the bench seat in my comanche and putting in some lance seats. Thanks much Tony KAPV N8389P *** Sent via http://www.automationtools.com *** Add a newsgroup interface to your website today.

http://www.alexisparkinn.com/rec_aviation.htm The Rogue's Gallery is a webpage specifically for users of these Rec.Aviation newsgroups. Here you may post pictures of your aircraft, your hangar, your airport, your family -- whatever -- free of charge, for the rest of us to see and admire! After...

I was walking around the old girl yesterday and the doors were hanging open to make sure all the moisture from the leaks (stand-by for post on cabin leaks)....so anyway, something made me grab the bottom of the door and check sop in the hinges. Maybe it was because I am thinking of taking them off...

OK, dumb question. For 100-hour inspections (or 50 hours until oil change), is this measured in Hobbs time or Tach time? -Sami N2057M, Piper Turbo Arrow III

The paint shop nearest me wants $7K to do a 152 (2 colors). I can't justify that for a $20K bird; the current paint isn't that bad. Is there any way at all to get a real paint job done for, say, closer to half that??

I purchased a C0 Experts Model 2002 about 1 month ago (it is quite precise and I am generally pleased with it). When I am climbing out from take-off, I am experiencing relatively high readings of CO, on the order of 30 Parts Per Million (PPM). This only lasts about 20 minutes or so. At cruise,...

I'm coming up on annual time for 24P, and as usual I'm planning to take advantage of the fact that the thing is taken to bits to make some improvements. On the list this time around are new fuel cells, new gear harnesses and switches (since there's no evidence that they've ever been replaced and...

Is there one? I would like a brighter landing light -- but I ain't paying $800 for it! -- Jay Honeck Iowa City, IA Pathfinder N56993 www.AlexisParkInn.com "Your Aviation Destination"

I understand that if I had a CHT, and it had a redline (I don't have one at all, probably because the PA-24 doesn't have cowl flaps) I would need to keep my CHT or get something certified to be a primary CHT. Are there any rules regarding EGT? The one I have is pretty useless. It's an analog...

I would like to start doing my own 50-hour inspection. I would like to have "the service manual", which I understand specifies the procedures for the 50 hour inspection. I own a Piper Turbo Arrow III. Do I get the manual from Piper, from TCM, or is their one for the plane and one for the...

I was just reading both the land lease, and hangar keeper agreements for the now City owned Morey Airport. (C29), and they both state: "The Lessee further agrees not to transport, or cause to be transported, onto airport premises, gasoline or other flammable fluids for the purpose of self-fueling...

Our 1964 Skyhawk has a placard by the fuel cap indicating that it is approved for unleaded auto fuel. However, I don't have any paperwork showing that it has an STC for autofuel. Any ideas on how I could research this information? Or...is the placard all I need? Thanks. -- Al Gilson Spokane,...

AOPA just posted a request that owners of series 400 Cessna aircraft provide some info on their aircraft in an attempt to limit the damage of the proposed AD (*you* know which one). http://twin.cessna.org George Patterson This marriage is off to a shaky start. The groom just asked the band...

Looking for a good salvage yard to buy a used top 1/2 of a tail cone for an Archer II. Thanks -- Jim Burns III Remove "nospam" to reply

Where can I get one? I looked at places like Aircraft Spruce and found nothing. My panel is cracked and chipped in numerous places. It looks like crap. I know you can buy replacement panels without the holes drilled for chearp. I can take care of the holes.

To make a long story mercifully short, RST is looking for a person to do the accounting function. While there are hundreds of thousands of beancounters in the area, there are darned few that understand that all small airplanes aren't yellow with a small bear painted on the side {;-) We don't need...

I rebuilt one and the best A&P on the field rebuilt the other one, on 1966 and 1957 172's. Neither will hold nitrogen. What's the secret to getting them not to leak. I bought a complete O-ring kit from Trimcraft in Wisconsin. My personal A&P told me that only one or two large O-rings were...

Anyone Know Ware I Can find some comfortable Inertia Reel Shoulder Harnesses for my 150 only one's I have been able to find are solid mount not Inertia Reel.

I have a KMA20 installed with 2 KX175B's. Where do I set the AUTO,COM1,COM2 toggle and rocker switches? I do have a 4P intercom and speakers. I would like to set COM1 as primary and COM2 on 121.5 for monitor. Thanks Cliff

We need to renovate the seats and perhaps side panels of our Archer II based at McCollum (RYY). We plan to do this while it's down a few days for the annual in June. We can pull the seats and panels and take them somewhere if that helps... I'd be interested in hearing of the experience of...