|
|
Benchtops & Shelving by
Jim Weir
I'm about to start building the "furniture" for the hangar. After a lifetime of
building "manly" workbenches out of DF 4x4s milled to take 2x4 crossmembers, and
having the concomitant rot and deterioration of wood, I'm considering making the
framing out of 1¼ PVC Schedule 40 pipe and fittings. ...
( 1 2 3 ... Last Page)
|
|
30 |
1,559 |
|
|
Bend over, folks... by
cavelamb himself
CBS news story about the Department of Homeland Security decision
to require identification of all operators and passengers of all
private boats and planes...
http://www.cbsnews.com/stories/2007/06/16/eveningnews/main2939438.shtml
We have met the enemy - and he is us...
( 1 2 3 ... Last Page)
|
|
125 |
5,581 |
|
|
Bending brake capacity: 2024-T3 vs. mild steel? by
Ihab Awad
Hi folks,
Most bending brakes rate their capacity by the thickness of mild steel
that can be bent. How does this relate to capacity of 2024-T3 aluminum?
So, what aluminum thickness can a 16ga, 20ga, 22ga, ... brake handle?
Should I simply multiply by the ratio of the yield strengths? That
somehow...
|
|
2 |
2,332 |
|
|
Bending extruded angle by
Veeduber
To All:
Extrusions of every type are common stuff in airplanes but many homebuilders
may not be aware of the fact the extruded shape usually receives additional
forming. Extruded angle, for example, may be opened or closed by as much as
twenty degrees (depending on the alloy). It is also common...
|
|
8 |
1,426 |
|
|
Bending graphlite rod by
[email protected]
The data on the Marske website about the graphlite (TM) rod they use
indicates
a glass transition temperature of 212F. So I tried heating some with a
heat gun
to see if I could put a permanent bend in it. No luck.
I think maybe it uses a phenolic resin which is thermosetting, rather
than...
( 1 2)
|
|
15 |
1,595 |
|
|
Bending longeron by
J.Kahn
I need to make bends of about 30 degrees in a 3/4 x .049 longeron tube,
with a tight bend radius, no more than 3 inches. Can I do the bend hot
without wrinkling the tube by free bending or do I need a supporting die
of some kind? Anybody have any specific techniques?
John
( 1 2 3)
|
|
29 |
1,040 |
|
|
bendix carb question by
Dick
My old C-85 has a Bendix Stromberg NA-S3A1, which is leaking for a time
after shutdown.
Previous owner of the plane had tied off the mixture control so shutdown is
by reduced throttle and magnetos turned off.
Casual conversations are leaning towards a needle seat or float level
problem. Any other...
( 1 2)
|
|
11 |
3,126 |
|
|
Bendix drives. by
JDupre5762
I have a customer with a pair of factory reman IO 540s with less than 100 hours
on them. After landing he will sometimes find the bendix drives on the
starters partially and occasionally fully engaged. It does not happen every
flight but sometimes every other flight. On at least two occasions...
|
|
6 |
2,201 |
|
|
Bendix King KY 97A TSO VHF Communication Transceiver by
NEW-USER
For Sale NEW
Bendix King KY 97A TSO VHF Communication Transceiver listed on ebay
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&ih=002&sspagename=STRK%3AMESE%3AIT&viewitem=&item=120227222035&rd=1
or
Item number: 120227222035
|
|
0 |
2,113 |
|
|
Bendix Magneto Question by
Dick Kurtz
I have an engine going into a homebuilt that uses the bendix D-2000 series
dual magneto. I have ordered a crank triggered ignition system to fire one
set of plugs and would like to replace the dual magneto with a single
magneto to fire the other set of plugs. The Starting functions will...
|
September 22nd 05 08:51 AM
by KDB
|
1 |
816 |
|
|
Bendix S4RN21 magneto by
Heino & Deanne Weisberg
I am looking for a Bendix S4RN-21 magneto to purchase.
I have for sale a Bendix S6RN-21 magneto in great running order.
Heino
|
|
0 |
2,110 |
|
|
Bends, kinks and splices by
Michael Horowitz
How does an A&P know if he can simply straighten out a longeron or if
he's going to have to cut and splice? Obviously if it has a kink in
it, it's very weak and would have to be spliced. Is there a reference?
In the meanwhile I'll go read AC43.13 and see what they say.
..
..
..
..
..
|
|
9 |
783 |
|
|
Bensen Days Fly-In by
GyroMike
Sunstate Wing and Rotor Club (EAA chapter 1192 and PRA chapter 26) will
be hosting the annual Bensen Days Fly-In in Wauchula Florida, March 29
- April 2, 2006.
More information can be found at Sunstate's website:
http://www.pra26.com/content.php?content.9
|
|
0 |
616 |
|
|
Bergstrom Plank by
keepitrunning
Could someone point me to a picture and information on the Bergstrom plank.
I think it is a single place delta wing sailplane. I spotted an aircraft at
Jean airport near Las Vegas that has that appearance but it had a Volkswagen
engine. There was no N number or data plate that I could find. ...
|
|
1 |
509 |
|
|
Bernard Pietenpol cub w/ Corvair by
Robert Loer
Can anyone tell me where to find a copy of the article I have read before
regarding Bernard's installationof a Corvair in a Cub? I want to know what
size prop he used.
thanks
Robert Loer
|
|
1 |
965 |
|
|
Bert Sisler& Cygnet by
dan
--
Dan Tappan
Looking for information on Bert Sisler.EAA no.1763. Does anyone know he is
still around and where?
Contact me of list at .]
Thanx
TldrgrDan
|
|
1 |
1,367 |
|
|
Best all time fly boy pictures by
Dale Alexander
Hi all,
I'm trying to put together some kind of plan to increase our EAA chapter
membership. To that end, I would like to pick everyone's brains for their
favorite big screen movie that involves airplanes, either main to the plot
or of any background significance. Examples would be like "Flying...
( 1 2 3 ... Last Page)
|
|
54 |
1,730 |
|
|
Best Alodine by
Larry Smith
I'm using DuPont's Aluminum Conversion but it doesn't work as well as some
I've seen. I want a little better etch. Also it is too expensive. Who
has a better source? The old literature speaks of a powder form chromic
acid etch. Anybody know where to find it at a good price? Thanks.
|
|
6 |
1,231 |
|
|
Best coax for aircraft radios by
ELIPPSE
If you would like to have the finest low-loss, light-weight coax cable
for your aircraft radio installations, get Andrew FSJ1-50A Heliax
Superflexible Foam Cable. It's pricier than the RG's, but the
performance is so far superior that your com, VOR, Xpndr, and whatever
will give you range...
( 1 2 3)
|
January 13th 05 05:20 AM
by Dude
|
24 |
1,196 |
|
|
Best Day For Sun n Fun? by
Greg Akers
I can go to the show on either the 13th or 14th. Which would be better. I
want to check out as many planes on the flightline as possible. Any ideas on
which one would be better?
Thanks
Greg
|
April 5th 04 05:06 AM
by EDR
|
3 |
689 |