Wheredidja go Dan ??

I accidently wrote my first post as a reply to another thread, so here it is again on its own. I have a pusher airplane with a nose oil cooler. I am replacing the existing heavy hydraulic type(rubber/braided steel) oil cooler lines with lighter metal lines. Either soft Aluminum or soft copper 1/2...

Our EAA chapter has received a donation of a Pulsar "Quick Build" kit that has languished in a hangar for several years. Looking at the materials, it is apparent that some of it has been exposed to sunlight coming through windows. The exposure is enough to discolor those areas that were not...

Greetings all: Do any of the inhabitants or R.A.Hombuilts know of Detroit/Flint/Ann Arbor Michigan area owners or builders of Cassutt I, II, IIIM or Sonerai I aircraft that would not mind a visit by local Ypsi builder? Curtis Scholl

Hello all, Short of looking through the docs of all the possible GPS' out there I am hoping I can get a general, if not, specific answer to the following. Do any of the handheld aviation GPS' have the capability to display location in UTM, MGRS, and different datums such as NAD 27 or WGS84? I...

Does anyone know of any DER's that know anything about composites? Thanks, Bob Gaines Marietta, Georgia USA

well I have a semi truck and a light bar with 12 marker lights in the bumper I am going to wire them 6 and 6 so when I turn on the turn signal they flash the right way 6 will flash right and 6 will flash left I would like to go further and make them flash in a seires 1,2,3,4,5,6, how do I do this....

Did I miss anything? Dave 'lost in civilization' Hyde

I'm looking at an older single seat Zenair with a 1835cc VW, but no starter. It does have an alternator. Is it possible, and if so, how big of a deal to add a starter? I'm not a big fan of hand proping... Thanks

Bryan Martin wrote: The DAR came out Saturday to do my airworthiness inspection and signed off the papers. Today I took the plane up for its first flight at Midland Barstow Airport in Midland, MI. I had to cut the flight short due to high oil temperature but other than that, things very...

It was getting on towards 2:30 in the afternoon and my passenger was a little anxious about getting his wife to a 3:30 doctor's appointment. We had just fueled up at Shelton airport and were headed back to Port Orchard and my pickup truck. I leveled off at 1,500' and pushed the throttle in. ....

I saw your statement: "I own a Champ' but like most Aeronca owners I've become a bit of a buff on the whole line" on the "Can I fly it at night?" thread. Do you know of a source where I could obtain a list of all of the side-by-side seating Aeronca models/years that were factory equipped...

It started with building a long driveway... two airplanes have already landed on it, and I who never even thought of kitplanes before am now thinking of building one. Being kinda lost with all the available types, I have noticed large differences in prices, such as between the Eagle-II and the...

For my little wargames, I've aquired some WW2 planes and I intend to play "bomb the Krauts" again and again. How can I repair an old B17, so that I'm able to bomb the Krauts again???

I've been offered a set of streamlined stainless wires for my bipe project that have come off a ground looped airplane. The vendor says that only one was very slightly damaged, the threaded end being bent just enough that the rod end wouldn't screw in al the way. He straightened it with a...

just makeing sure my news stuff is up and working ..back to laying up my wing on a long ez . need more peel ply

After my original stopped working, I orderd a Westach hourmeter from A.S. Supply. It does not work and before I send it back, thought I might check my troubleshootinmg logic G as it seems unlikely I'd get a bad meter. In plane: confirmed ground and hot leads installed properly on meter backside...

$MAKE LOTS OF QUICK CASH THE EASY WAY$$ Dear Internet User, Good day, This article I've written is all about the fact where I earned an ASTOUNDING amount of money in less than a month and I've decided to share or reveal the secrets behind making big bucks in the Mail Order Business. So all money...

I want to build a cable to run my M1 & M3 at home in demo mode. Both navigators use the same connector & pinout for their power (connector P15 on M3, not sure about M1). The connector looks like a Centronics 24-pin, but the edges are more rounded. I showed my local electronic store my M3 but...