|
|
Advice on Partnerships by
Jay Moreland
I would like to be able to share expenses and work on my experimental
aircraft now and in the future. I would like to have a partnership with
several others both to build and to operate an experimental 4 to 6 place
aircraft. Perhaps, especially in building, this is not advisable. I
would like to...
|
|
1 |
1,070 |
|
|
about lycoming IO360 A1B6 by
Philippe Vessaire
Hello,
Is this engine is #1 or #2 dynafocal mount?
Thanks
--
Minicab F-PRAZ
Philippe Vessaire Ò¿Ó¬
|
March 12th 07 09:14 PM
by jls
|
1 |
1,070 |
|
|
Flying Car by
jls
http://www.theregister.co.uk/2006/01/23/flying_car/
( 1 2)
|
|
18 |
1,070 |
|
|
lanier paraplane? by
patrick mitchel
Anyone have any info on the lanier paraplane(and the II version)? 20 mph
landing speed and a 150 mph cruise seems a lot like the claims on the
infomercials for kitchen gadgets. TIA Pat
|
|
1 |
1,070 |
|
|
The Wright Flyer yesterday by
Michael Horowitz
Yesterday's coverage pointed out two things that caught my ear:
First, that it was a considerable amount of time before the Brothers
were able to duplicate the longest flight of the day, and second, that
the craft was (apparently) just on the edge of being able to fly.
So, anyone know what aspect...
|
|
2 |
1,069 |
|
|
Carpeting options? - New Cessna's as an example by
BellSouth.net News
On the new Cessna 172's, Cessna uses a Black mat type carpeting in the
front, then it goes to actual carpet in the back.
I'm looking for a source for the black mat in the front to do the floor in a
Mooney. Anyone know what they use or where I might get some? I believe
it's a polypropylene type...
|
|
2 |
1,069 |
|
|
|
|
1 |
1,068 |
|
|
Removing Rusted Sparkplugs by
Michael Horowitz
Folks - I'd like to remove my plugs and see how they look. Externally,
they look like they may be rusted in place - don't know for sure,
havn't tried to undo one. Any suggestions on how to approach the
possibility they may be rusted in place? Lots of penetrating oil? -
Mike
|
|
4 |
1,068 |
|
|
Hatz Yahoo Group by
Scott
I'm a Hatz Classic builder and for the last few months, I and other
Hatz builders have been unable to access the forum on the Hatz Biplane
Association web site. Out of frustration and the need to communicate
with other Hatz builders, I created a Yahoo Group called Hatz_Biplane.
The new Yahoo Group...
|
|
2 |
1,067 |
|
|
KR-20 manual by
Juan Jimenez
For those of you who may find a need for this (which probably won't be too
many of you), I put my copy of a KR-20 marker beacon receiver install and op
manual (with pinouts, that's why I put it up), on the site. You can download
a small PDF file at http://www.bd5.com/kr-20.pdf
Juan
|
|
0 |
1,067 |
|
|
Weld over brazing by
Michael Horowitz
This is not aircraft related.
I did some brazing on a tank and then later decided it would have been
easier to have welded.
I read somewhere that one should not attempt to weld over brazing.
I assume becase the brazing material melts at a lower temp than the
base metal, that welding over a braze...
|
|
2 |
1,067 |
|
|
Avionics -- superflags by
Michalk
What are the 400mA current sink superflags used for? I've got them on
my Apollo equipment, but they only show hookups to older equipment.
|
November 28th 04 05:22 PM
by Michalk
|
0 |
1,066 |
|
|
Need Advice On Ferrying Foreign Registered Homebuilt To USA by
S Ramirez
I am interested in flying a homebuilt aeroplane from Greece to the USA and
have it registered to an N number. Does anyone here have any knowledge of
how hard or easy it is to do this? I have concerns like flying it from
country to country in Europe, flying it to Iceland, then Canada, then...
|
|
2 |
1,066 |
|
|
Defiant Info by
David Culbertson
Looking at purchasing a Rutan Defiant. Has anyone flown one and if so do
you have any recommendations before I make a purchase. What did you
like/not like? Would you recommend buying?
Thanks
Dave Culbertson
|
|
0 |
1,066 |
|
|
can I help on your project around KCDW? by
[email protected]
I know nothing about kitplanes/homebuilts but want to learn. If you want
help or just to teach me something about it post here and i'll get your
email address. I'm around CDW, private pilot, low time, etc. I don't
have a garage nor the funds to start my own project any time soon which is
why i'd...
|
|
0 |
1,065 |
|
|
|
|
0 |
1,065 |
|
|
Pinckneyville flyin time again ... by
John Ousterhout[_2_]
I've added a link to Highflyer's official announcement to my Unofficial
Pinckneyville FAQ. http://www.ousterhout.net/pjy-faq.html
If I'm reading my webstats properly over 200 people have read the
Unofficial FAQ in the past few days. Unbelievable!
- John (back home again in Oregon) Ousterhout -
|
|
7 |
1,065 |
|
|
?replace bushing on compressor wheels? by
mhorowit
One of the wheels on my air compressor is at an angle. I removed it
and the bolt/spindle and the inner and outer bushings wiggle.
Anyone know if it is worth replacing these bushings and how to do it
or should I just buy a wheel? - Mike
|
September 22nd 08 03:43 AM
by Ricky
|
4 |
1,065 |
|
|
IFR PANEL by
Flyhighdave
I am starting to plan out my panel and want to be able to have the capability
of doing basic IFR operations and approaches in the future. I want to make sure
I have room, in a logical location, for the equipment that will be needed.
So my question- What equipment will be needed on the panel for...
|
|
4 |
1,065 |
|
|
P-Leads getting hot by
Justin H
I tried starting my engine today after a top overhaul, the right P-Lead got
really hot and smoke came off it when I hit the starter button. where should
I start looking for a short? could it be shorting back thru the starter
motor?
|
|
8 |
1,064 |