http://makeashorterlink.com/?R24822E6C

My Chapter is featured in the January issue of Sport Aviation. It is a pretty good article! See: http://eaa288.org/ -- Remve "_" from email to reply to me personally.

Two NEW unmounted Tn Props, 60x32 and 60x28 both clockwise rotation facing prop. Two Bing carbs. Model 57. Email me

EAA has just started a new site. Interviews with some well known people in Aviation. Many of use know some very well know aviation people that are up in age and should be interviewed for 5-10 minutes. I talked to the EAA Director of this program today and he said they are looking for interviews...

Anyone know any good sources for these. It seems like I will be needing a nice repeatable one in the 5-100 in/lb range for 10-32 screws and nuts. I am not sure what the torque is that I will be using, the screws are AN509-R10 (MS24694 #10) and the nuts are MS21040-3. I have seen from 20 in/lbs to...

Evening all. I started a similar thread a while ago, but have done some more reasearch since. I will be sending this post to SAAA, to see what they think. As I understand it, you may put an auto engine into a certified aircraft in australia, and the legislation states that a request to do so must...

Atkins lists the weight of their single rotor "industrial" version of the Mazda 13B at 80 lbs and their marine version at 130. I've got most of a 13B apart on the shop floor with the idea of building a truncated version for aviation use but I'd like to know if the weights are anywhere near real...

I was wondering about the feasability of covering a wing on an ultralight with Monokote, which is normally used on R/C aircraft. If the tensile strength is too low, could you use 2 or more layers?

BWB better watch out. Here's a warning note from a friend who lives on the Baja: "We just had the forth Cessna 210 stolen down here at Punta Pescadero. Somebody must get info from immigration. Only the 210s are being stolen. If I had that much money invested in an airplane, I would have a...

....Inquiring minds wanna know.

While it was a busy day on the airways (radio wise) I got the same result calling up ATC 15 miles out; 'scratchy but readable'. Tried reaching around back of the seat to key the rear PTT but it was too painful wating for the frequency to open up. I did try calling another aircraft at an airport 55...

http://makeashorterlink.com/?R24822E6C

I saw your statement: "I own a Champ' but like most Aeronca owners I've become a bit of a buff on the whole line" on the "Can I fly it at night?" thread. Do you know of a source where I could obtain a list of all of the side-by-side seating Aeronca models/years that were factory equipped...

Did I miss anything? Dave 'lost in civilization' Hyde

Apollo SL40 VHF Comm Garmin GTX 320A Transponder Both of these are brand new but there are no trays. I do have the user's guide for both. Make a fair offer. I can take paypal. Howard

I've got some slight cracking in my aluminum nosebowl and have stop drilled them twice. I'm considering backing the cracks with fiberglass in hopes to keep the vibration down. How well does fiberglass adhere to aluminum? What system is better. I have easy access to the West system chemicals. Any...

(Necessary Aviation Content: Weight) (Necessary Aviation Content - Part Deux: Piper entrance and egress) Anyone looking to shed 'a few' pounds this year? If you've succeeded it in the past, want to share your story? Montblack If food is my cocaine, I'm the Darryl Strawberry of weight loss...

four point (square) sockets (and/or wrenches) who makes them, who retails 'em?

Anybody had any experience Peeling Protective Paper from Plexiglass??---When it's old & dried out---everything I've used to try to soften the old glue also softens the plexi & leaves it with an orange-peel finish. I have several 12" sq pieces, the center will finally come once you get out there,...

Has anyone used "Aircraft Finishing Systems"?