Under current australian regulations, it is my belief that to be registered experimental you have to build a majority of the aircraft yourself, from parts, kits, whatever, so, you are not permitted to put say, an automotive engine onto the front of a certified aircraft and register it...

Morning all. Is someone able to point me in the right direction to find the legislation/Acts/Regulations etc in relation to de-certifying aircraft in canada, to experimental status so mods can be done. Seems like a good and logical idea. Many thanks in advance. Rob Melbourne, Australia.

Evening all. I started a similar thread a while ago, but have done some more reasearch since. I will be sending this post to SAAA, to see what they think. As I understand it, you may put an auto engine into a certified aircraft in australia, and the legislation states that a request to do so must...

Corrie wrote that his someday mobile is an Emeraude. I've never heard of it. The dream on my wall is the Lanceair turbine. But I'll have to get a few more places rented before I can play that game. Maybe change my mind by then too. It's a while off. Forrest

The following is an email I sent to Jim Weir of KitPlanes Magazine. Jim requested that I post my message to this newsgroup and and open these issues up for discussion. I'm the new guy to aviation. Your Areo 'Lectrics column is like a much needed refresher course in

Richard Riley I will check it out. Thank you. Forrest

My wife normally does the computer stuff. So if some of my posts come off as novice, well, guess what..... I will post a couple of responses and pull out some of the repeated stuff as follows. On Sunday 7 Dec. 03 Big John wrote; "You didn't say how experienced you are. Don't think the bird is...

I figure that since I am quite new to aviation I must be coming off as kind of dim-witted. I'm rebuilding this KR-2. It is an experimental. So I am experimenting. And trying to do something large cool on small money. And not small in aviation speak but small in po'folk speak. I've spoken to...

Still getting to know my airplane. It's dimensions are not the same as either the KR-2 or the 2S. Still figuring out how I'm going to weigh the thing. Probably stack the parts on two or three scales then weigh the engine. I'll come up short of what the cowling would weigh since it was junky,...

I have to begin making a few decisions on how to drop a few pounds (off my butt and my airplane!) For one, I'm considering making the composite tank as outlined in Tony Bengelis' book. This would be the foam/glass sandwich he describes. Questin is, is it lighter than the aluminum tank specified in...

Some of the welding manuals I have say that a certain amount of undercut is inevitable. Certainly in examining the fuselages of some factory aircraft I've seen some shockingly large errors like this in the finished welds. On many of my practice wleds, particularly on tubing clusters, an...

Anyone know off-hand what the wheel track is on a Citabria? Either from the wheel centers, or even better, from the outside of the wheels? I need to know if I can fit it in a container with the gear on. Searched the net for the info, no dice..

Anyone have experience with these? Wag Aero are selling plans for these still. Anyone know of their history? were they always a homebuilt design? Are they compartmentalised like Edos? Performance? ease of building, expense? TIA! F1

Another stupid question! Been reaming holes in a few 4130 plates. The reamer worked fine for about 20 holes and then the holes started getting a bit smaller to the point the bolts got a bit snug. In my ignorance I thought this one hand reamer would pretty much last me the whole project, but...

Anyone know of a site or combination of sites with a comprehensive list of suitable props for a given airframe/engine combination? I've been keying in searches to beat the band and getting very little outside of Aircraft spruce's info. Fixed pitch only, BTW F1

I have access to a plating facility (aviation, but it's a jet engine rebuild shop) where I can get my wing fittings plated. My understanding is that 4130 cad plating is just that, cadmium and nothing else, but this shop does it's cad plating by a coating of nickel first and then cad plating.....

I've got a few metalworking books on eBay. All are in like new condition. This link should get you to the stuff I'm selling now, which includes the books. Sorry for the other stuff. http://search.ebay.com/_W0QQsassZfosterjj

Does anyone know of a reputable metal supplier who stocks aviation type aluminum in the Philadelphia/New York Area.

I thought that I understood the new Sport Pilot/Aircraft rules (first mistake) until I came across the fact that apparently you can buy a ready to fly CH601HD made by Zenair in the US that is registered as a sLSA, or you can buy the same ready to fly plane built by Czech Aircraft Works and register...

Can any one tell me how much signal I will lose if the ground plane is not directly under the radiating element? What if I have to move it 2' away, although still tied to co-ax shield?