THESE
https://www.walmart.com/ip/Unique-Bargains-50pcs-R-Split-Mechanical-Hitch-Hair-Tractor-Cotter-Clip-Pin-1-6mm-x-28mm/546161908
are what I use.Â* Never run out again.

If those seem too cheap, send me $139.95, and I'll send you 6 of them. :-D

On 7/29/2019 2:39 AM, John Foster wrote:
On Monday, July 29, 2019 at 2:15:06 AM UTC-6, James Thomson wrote:
At 07:57 29 July 2019, John Foster wrote:
On Monday, July 29, 2019 at 1:17:38 AM UTC-6, John Foster wrote:
On Sunday, July 28, 2019 at 6:09:07 PM UTC-6, Steve Bralla wrote:
On Monday, June 15, 1998 at 12:00:00 AM UTC-7, Al wrote:
Anyone got any good suggestions for clips for hotelier linkages.
I also understand that there is a sleave kit out there somewhere.
=20
Thanks
=20
Al
Sleeves? I can't help. Pins? Aircraft Spruce
https://www.aircraftspruce.com/catal...owlingpins.php
=20
Thanks for all the links, guys, but these are not the spec that is
called=
for in this AD. The glider in question is a Bolkow Phoebus, but I
believe=
this AD also applies to the Standard Cirrus, as well as some others
(corre=
ct me if I'm wrong). It specifically states the clip must be 1.2mm
diamete=
r wire, and gives a picture of the clip going across the push rod. In
this=
particular application, the push rod is only about 1/2" diameter, so a
cli=
p that is 1.5" long will stick out the sides too far and hang up on the
sur=
rounding structures. Here's a link to the AD:
=20
http://www.ltb-lindner.com/phoebus-ad-sb.html
=20
Look particularly at the PDF link "13 94_001 L`Hotellier
Verschluesse.pdf=
(94,4 kB)". =20
=20
It gives pictures and dimensions of the clip needed. It specifically
men=
tions a specific L'Hotellier part #140-31, or equivalent Ford part
number
1=
473 931, but neither of these part numbers come up with anything
other
than=
copies of the AD when a Google search is done. I can not find a
source
fo=
r these specific parts.

More specifically, these connections are for aileron and spoiler push
rods
=
that come through holes in the wing root rib. If the clips stick out too
f=
ar, they will snag on the edges of the holes in the wing root rib and
cause=
the control surfaces to hang up and not move properly. Obviously,
that
wo=
uld be very bad.
I think that you are getting the various locking devices confused! The
AD is issued by LBA - Google LBA 193-001/3 for the current version.
There are various locking methods to choose from - safety pins, Uerling
sleeves, LS locking sleeves, Schempp-Hirth clips, Wedekind sleeves are
all mentioned in the AD.

The L'Hotellier and Ford safety pins are very small and simply go through
the connector lock plate as shown on the second page of the Lindner
document. They do not go round the push rods or stick out to foul the
holes in the root rib.
Exactly. These are the type of connectors on my glider, and I am looking for a source for these "very small" pins. I realize there are other newer and better connectors, and one of those options may be in my future. But for now, I need to drill holes as mandated by this AD and use these specific small pins. Where can I find them?

--
Dan, 5J