A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Simulators
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Joy stick or wheel?



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #4  
Old October 5th 03, 06:17 AM
Marc
external usenet poster
 
Posts: n/a
Default


"CriticalMass" wrote in message
...

"Skyhawk" wrote in message
...

I would recommend the CH Products Yoke w/ throttle,mixture, and prop
controls. If you want to spend the big bucks, get the Pro Pedals as

well.
They are around $250 purchased at the same time or $130 each. I would

check
out the www.pcaviator.com web site. I have purchased from them with
success, and they have competitive prices. It is hard to find the good
controls at retail. As an alternative, the Microsoft Force Feedback 2
joystick works well and it is around $100.



While I won't argue with any of the above, I will add my comments.

I am now using CH USB rudder pedals, with no issues to report.

I *used* to own the CH Yoke with engine controls and all the buttons.
Believe it or not, the damned thing stripped the hardware-store clamp

bolts
that secure it to the desktop. I could no longer attach it to my desk and
use it to fly. It boggled my mind that such a low-tech item would tank,

but
it did. It went into the trash.

I will not buy from CH Products again. If they can't get an item like

that
right (and, mind you, I've been using their stuff for a L O N G time),

they
have lost my confidence.

So, I'm now flying the sim with the CH USB Pro pedals and a Microsoft FFB2
force feedback joystick.

I agree that flying most of the sim airplanes is best enjoyed with a yoke,
as opposed to a stick. I'm waiting for something more durable than the CH
yoke to surface on the market. I have the bucks, and I'll spend them, if
that's what's required to get *quality* flight sim controls.


I had two of those, and no problems with the bolts. The bolt itself is a
stainless steel standard piece of hardware -- type SBY, which can be
obtained at a hardware store. It is epoxied into the knob. The socket into
which the bolt fits is brass and pretty durable. I don't see anything poorly
made about these parts, but they are easy to replace if they should go. In
any case, I would not judge a flight yoke by the bolts that hold it to the
desk, that is a pretty minor part.

I have held off getting the rudder pedals. Are they useful? Seems like a lot
of money for something that doesn't get used too often. In a crosswind I
just land a little kilter -- unlike the real thing, there are no repair
bills for damaging the virtual main struts, at least not so far.

Question, do any of the virtual airplanes accurately simulate a forward slip
using the rudder pedal - including rapid loss of altitude, etc.?

thanks



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Piper 6.00x6 Nose wheel and fork? mikem Owning 2 March 6th 04 07:23 PM
Piper 6.00x6 Nose Wheel and Fork? mikem Products 5 March 5th 04 11:34 PM
VW-1 C-121J landing with unlocked nose wheel Mel Davidow LT USNR Ret Military Aviation 1 January 19th 04 05:22 AM
Tailwheel endorsement John Harper Piloting 58 December 12th 03 01:48 PM
The Little Wheel in Back Veeduber Home Built 6 September 8th 03 10:29 AM


All times are GMT +1. The time now is 11:14 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 AviationBanter.
The comments are property of their posters.