A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Home Built
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

AN ENGINE FOR HOMEBUILDERS



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #13  
Old May 22nd 09, 05:17 PM posted to rec.aviation.homebuilt
[email protected]
external usenet poster
 
Posts: 13
Default AN ENGINE FOR HOMEBUILDERS

On May 21, 10:21*am, wrote:

One quick question, will a motorcycle chain system work for a prop?


Hey Canuck,

Where-the-hell you been for the last 106 years? Take a look at a few
old photos and you'll see the answer to your question. Now before
everyone assumes that they know where I'm going with this response,
let me dispell a few myths:

1. it was NOT a bike chain. It was a #35 solid-link chain made by
Diamond. Two props means only 5.75hp per prop, so the #35 was the
correct size for our two brothers from Ohio (same size would work well
on a go-cart).

2. The two biker-brothers from OH were NOT the only ones to use a
chain PSRU successfully. Ben Epps did it in 1907. And some Italian did
it in the teens. Never did identify that plane, but it was a flying-
boat with a high-mounted chain-driven prop.

3 Tortional (sp??) vibration would be a serious issue if you don't
know about the working solution for it. That being a prop-shaft made
of spring-steel. Think tortion-bar suspension. Wil and Orv discovered
this the hard way by cracking two sets of tubular prop-shafts before
treking back home and making a suitable replacement. (Oh yea, don't
forget to squirt a little "Arnstein's tire cement" on the threads of
your shaft nuts or they'll come loose.)

Now would a modern motorcycle chain work? You bet. Would it be really
heavy? You bet. Could you find a suitable airframe that would handle
the weight, deal with the vibes, and last a reasonable amount of time?
Hmmmm. One thing is certain about chains though. They typically draw
1-3% of the engine's power. A belt is usually 5-15%. That's why you
don't see too many belt-driven bicycles out there.

If it were me, I'd be inclined to try two B&S Vanguards driving
outrigger-props via chains or serpentine belts on a test-bench just to
see what I could get. Probably a waste of time, but we are here to
experiment. Too bad all of the small I/C diesels are rediculiously
expensive and super-heavy.

Hey Euro-pilots, got any small diesels that might work with direct-
drive? No dice here in the States. Diesel here equals truck.

Harry

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
A Camcorder for Homebuilders [email protected] Home Built 3 June 1st 08 03:27 PM
Mexico City - Homebuilders ... ......... :-\)\) Home Built 2 February 7th 05 12:04 PM
Is this the place for Homebuilders? Gilan Home Built 2 September 23rd 04 02:06 PM
NPR Segment on Elderly Homebuilders Jay Honeck Piloting 0 May 29th 04 11:32 PM
Best Homebuilders Books? [email protected] Home Built 5 January 21st 04 01:06 AM


All times are GMT +1. The time now is 12:25 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 AviationBanter.
The comments are property of their posters.