If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
dimpling
When I dimple holes in thin sheet they get larger to the point where the
clecos won't hold. Should I drill holes that are to be dimpled for 1/8 rivets a little smaller (like #31 or #32)? What are others doing? Mike Murphy Moose. |
#2
|
|||
|
|||
"Mike Rapoport" wrote in message k.net... When I dimple holes in thin sheet they get larger to the point where the clecos won't hold. Should I drill holes that are to be dimpled for 1/8 rivets a little smaller (like #31 or #32)? What are others doing? Mike Murphy Moose. Never had that problem and I did a bunch of drilling and dimpling on the RV-6. Are you drilling #30 to start with and using quality dimple dies? I hate to ask, but are you using the copper colored clecos, or have you accidentally dipped into the silver ones? Another option is that your cleco's are worn out. Any chance of that? KB |
#3
|
|||
|
|||
Kyle Boatright wrote:
"Mike Rapoport" wrote in message k.net... When I dimple holes in thin sheet they get larger to the point where the clecos won't hold. Should I drill holes that are to be dimpled for 1/8 rivets a little smaller (like #31 or #32)? What are others doing? Mike Murphy Moose. Never had that problem and I did a bunch of drilling and dimpling on the RV-6. Are you drilling #30 to start with and using quality dimple dies? I hate to ask, but are you using the copper colored clecos, or have you accidentally dipped into the silver ones? Another option is that your cleco's are worn out. Any chance of that? KB Another problem I had whem I bult my RV-6 was I had bought a bunch of generic "clecos" from ATS and they were all junk had to throw them all away. Make sure they are the Cleco brand or Wedgelock brand most other brands are junk. Jerry |
#4
|
|||
|
|||
I am using cleco brand and, yes, I am using the copper ones. The dimple
dies are the "springback" ones from US Tool. The skins are 6061 if that makes a difference. Mike MU-2 "Kyle Boatright" wrote in message ... "Mike Rapoport" wrote in message k.net... When I dimple holes in thin sheet they get larger to the point where the clecos won't hold. Should I drill holes that are to be dimpled for 1/8 rivets a little smaller (like #31 or #32)? What are others doing? Mike Murphy Moose. Never had that problem and I did a bunch of drilling and dimpling on the RV-6. Are you drilling #30 to start with and using quality dimple dies? I hate to ask, but are you using the copper colored clecos, or have you accidentally dipped into the silver ones? Another option is that your cleco's are worn out. Any chance of that? KB |
#5
|
|||
|
|||
Mike, Veeduber recommends that one drill with a #40, deburr and then dimple with the 1/8" dimple dies. I have done some like that and some using the #30 drill first. Sometimes I have to 'open up' the hole a bit with a reamer when trying to put in the rivet when I use the #40 bit first. Veeduber's advise was in reference to using blind rivets iirc. The springback dimple dies are meant for dimpling fuel tank skins so that smearing sealant will not make the rivet stand proud of the dimple so I think they may be a few thousandths oversize. Hope this helps and remember all advice is worth what you paid for it! Bruce |
#6
|
|||
|
|||
"Bruce E Butts" wrote in message ... Mike, Veeduber recommends that one drill with a #40, deburr and then dimple with the 1/8" dimple dies. A 1/8" dimple die won't fit in a #40 hole, which is roughly 3/32. I have done some like that and some using the #30 drill first. Sometimes I have to 'open up' the hole a bit with a reamer when trying to put in the rivet when I use the #40 bit first. Veeduber's advise was in reference to using blind rivets iirc. The springback dimple dies are meant for dimpling fuel tank skins so that smearing sealant will not make the rivet stand proud of the dimple so I think they may be a few thousandths oversize. Most of the high quality dimple dies are of the springback configuration. They are good for dimpling everything that needs to be dimpled, not just tanks. They are not oversize. Some of the tool vendors sell special tank dyes which produce a slightly deeper dimple, but that isn't a function of whether they are springback dyes or not. Hope this helps and remember all advice is worth what you paid for it! Bruce KB |
#7
|
|||
|
|||
Whatcha need to do is take a little scrap of aluminum with the correct
size hole in it. When you put the cleco through your part, you put the scap on the end of the cleco and that will "clamp" the parts to your cleco. John |
#8
|
|||
|
|||
John T wrote:
Whatcha need to do is take a little scrap of aluminum with the correct size hole in it. When you put the cleco through your part, you put the scap on the end of the cleco and that will "clamp" the parts to your cleco. John Doesn't help if he's closing a part or has a bunch of holes that need clecos. If he really needs to do as you suggest washers are cheap and smaller than you the scrap you suggest. I can't imagine a situation where one would need to use a back up if one is using proper proceedure and good tools. Dan, U.S. Air Force, retired |
#9
|
|||
|
|||
Hi Mike
It may be an issue with the 6061 skins cuz I found the same problem when I was building my rebel. I used the cheap dimpler that has a nail through the centre or the same dies that I welded to a pair of vice grips. Drilling 3/32" then dimpling then opening up the holes to #30 worked for me. I am using cleco brand and, yes, I am using the copper ones. The dimple dies are the "springback" ones from US Tool. The skins are 6061 if that makes a difference. Mike MU-2 "Kyle Boatright" wrote in message ... "Mike Rapoport" wrote in message k.net... When I dimple holes in thin sheet they get larger to the point where the clecos won't hold. Should I drill holes that are to be dimpled for 1/8 rivets a little smaller (like #31 or #32)? What are others doing? Mike Murphy Moose. Never had that problem and I did a bunch of drilling and dimpling on the RV-6. Are you drilling #30 to start with and using quality dimple dies? I hate to ask, but are you using the copper colored clecos, or have you accidentally dipped into the silver ones? Another option is that your cleco's are worn out. Any chance of that? KB |
#10
|
|||
|
|||
You might also try asking at the murphy builders group mailing list.
https://www.dcsol.com/public/code/html-subscribe.htm I am using cleco brand and, yes, I am using the copper ones. The dimple dies are the "springback" ones from US Tool. The skins are 6061 if that makes a difference. Mike MU-2 "Kyle Boatright" wrote in message ... "Mike Rapoport" wrote in message k.net... When I dimple holes in thin sheet they get larger to the point where the clecos won't hold. Should I drill holes that are to be dimpled for 1/8 rivets a little smaller (like #31 or #32)? What are others doing? Mike Murphy Moose. Never had that problem and I did a bunch of drilling and dimpling on the RV-6. Are you drilling #30 to start with and using quality dimple dies? I hate to ask, but are you using the copper colored clecos, or have you accidentally dipped into the silver ones? Another option is that your cleco's are worn out. Any chance of that? KB |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Dimpling and riveting pressures | Max Krippler | Home Built | 5 | November 11th 03 08:03 PM |