A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Owning
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

windows



 
 
Thread Tools Display Modes
  #1  
Old November 24th 05, 04:13 PM posted to rec.aviation.owning
external usenet poster
 
Posts: n/a
Default windows


Warrior Windows.

A few weeks ago I asked if anyone has had any experience polishing out
damage to plexiglas windows caused by a sloppy painter who got paint
stripper on the plastic. No one has so I will answer my own question.
No, the penetration is deep enough that the remedy will be enough to
cause distortion. With that new information I ordered a new set of
glass from Great Lakes Aero and went to work. The AP installed the
windscreen and I tackled the sides. The job is straightforward enough
without inherent problems. Great Lakes plexaglas fitted perfectly
without any alteration. There were only three problems. First I tried
to cheat the system and do the job without removing the seats.
Contorting over the seats probably doubled the time necessary to do the
job. second the #4 screws holding the bracket retainers had corroded
or worn the screwholes enough to prevent the threads from engaging.
This is easily remedied but a nusiance. It is also a nuisance to
reinstall using the #4 screws. Next time I will have a handful of #6
screws. The third problem was not of my making. I opened a new tube
of GE "Kitchen and Bath" silicone. The first several feet of the
silicone was of noticably lower viscosity. The problem cleared up as I
went along. Bad mistake. The low viscosity material never set up, it
is still tacky, semifluid. I called GE to ask if I should give it more
time or start over. The lady listened to my story and opined that if
it had not set in a week it was not going to and that I should clean it
up and go at it again. I could almost see her shrug when she said that
it must have been a bad batch.
Total time for the job would be about 6 to 10 hours.

Ads
  #2  
Old November 25th 05, 09:31 PM posted to rec.aviation.owning
external usenet poster
 
Posts: n/a
Default windows


On 24-Nov-2005, wrote:

Total time for the job would be about 6 to 10 hours.




Just out of curiosity, how many of the 6 side windows on your Warrior do you
feel could be replaced in that amount of time?

--
-Elliott Drucker
  #4  
Old November 26th 05, 10:00 PM posted to rec.aviation.owning
external usenet poster
 
Posts: n/a
Default windows

The learning curve is not too steep - if I remove the seats and have
plenty of new screws I believe I can do all 6 in 6 hours. I don't want
a job. Leo

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
MSDOS FS 5.1 runnable under Windows 2000/XP? Bill Wolff Simulators 12 January 13th 04 08:05 PM
FS2002 failing with Windows XP - HELP !! Jim Kilpatrick Simulators 2 September 28th 03 01:33 PM
Real World Specs for FS 2004 Paul H. Simulators 16 August 18th 03 09:25 AM
Notebook PC Configuration for MSFS2004 Paul H. Simulators 0 July 18th 03 11:21 PM


All times are GMT +1. The time now is 06:45 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Copyright 2004-2021 AviationBanter.
The comments are property of their posters.