If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
Saratoga Gear Retract Problem
"john smith" wrote
John, which engine on the Seneca drives the hydraulic pump? The electric one bolted to the top of the powerpack-think Meyer snow plow. (Sound of Homer Simpson "dope slap") Can you tell I'm not a multi-pilot? :-)) Don't feel bad, it's the left engine on our Aztec, no electric hyd pump. Now... along those lines... what would cause a sudden "over flow puddle" from our Aztec's hyd system? Plane's annual was this summer, hyd system topped off with fluid, we've flown it about 40 hours since then. Saturday, the engines were due for fresh oil and filters so I took her out for a short joy ride to warm everything up. Changed the oil and filters but didn't have a chance to pull it back out and do a run up to check for leaks. So last night I go up to the hanger to do that and I notice a puddle of hyd fluid directly below the overflow tube near the rear of the nose gear wheel well. The drop hanging from the overflow tube confirmed where it was coming from, nothing else wet or washed off, but why? why after 40 hours of flying and probably a dozen gear/flap extensions and retractions would it decide to overflow any excess fluid at this time?? I was able to add about 6-8 oz of fluid to the system to top it off. Ran the flaps up and down, no leaks noticed anywhere, no additional overflow out the overflow tube. System fill tube stayed full. Any ideas??? TC what ya think?? Thanks Jim |
#12
|
|||
|
|||
Saratoga Gear Retract Problem
I think that raising and lowering a rubber hose to blindly
service/verify the proper level in a power pack reservoir is really goofy. Not sure if that's how yours works or not, but on the newer models the hose was clipped to the side of the nose. In the past, whenever I serviced an Aztruck pack, it would typically vent some on it's first or second (or third) flight, but it never appeared to be very much. I guess I would keep an eye on it to make sure that it isn't still venting, or if it does drip a little more, make sure that it stops after it decides it's at the proper level. TC |
#13
|
|||
|
|||
Saratoga Gear Retract Problem
I do remember it is real costly. My mechanic took out mine and cleaned
it up inside and now it works just fine. So you should look at that possibility. Lots of things are not repairable, but really are. I do recall all that troubleshooting cost me close to 3k$. John George Sconyers wrote: Sure hope my problem is the same as yours. I just ordered the $672 switch from Piper! Hopefully, my mechanic's discount he has setup with them will bring the price down 30%. Do you remember what you payed for the pressure limit switch (Piper part number 587-847)? -George "The Visitor" wrote in message ... I have a seneca 3. My problem started out like that, easy to sort of fly with. Then it got worse. Sometimes wouldn't at all retract, or just partially then pump would go off. We, flushed out and changed fluid, swaped up and down relays(they are the same), measured pump pressure, changed pump/motor, gear was in no way binding. The last thing checked was an over pressure limit switch that was going faulty and shutting the pump off. 2000 Saratoga? Mmmmm, nice. Our gear is probably similar in design?? Good Luck. John Yahoo! News wrote: During day one of my 2000 Saratoga's annual today my mechanic and I observed the following problem. If anyone has some experience with this or they have a mechanic that has experience with this I would love to hear about it: Here is a description of what we are observing: 1) Gear retraction is initiated with handle being placed into the gear up position 2) Nose gear and main gear unlock and start retraction 3) Gear Unsafe light illuminates simultaneously with gear unlocks 4) In about 1-2 seconds, nose gear completes retraction first (this is normal as far as what I have observed in the past both on my plane on jacks and on observing others from the ground departing from airports) 5) Main gear comes up part way but hesitates until nose gear completes retraction - again I believe this is normal 6) Main gear almost completes retraction in about 2 seconds after nose gear - a few inches from being completely retracted - this is where something has changed. 7) Pump Motor shuts off for approximately ¼ second 8) Pump Motor starts again for approximately ¼ second and gear moves up a little more (maybe ½ inch to 1 inch) 9) Pump Motor shuts off again and restarts again 3-5 times in the same pattern of quick off and ons before gear is completely retracted and pump motor remains off 10) Gear warning light extinguishes about the time or slightly before the pump motor shuts off for the last time This process is very repeatable. Only the number of quick off-on cycles of the pump varies slightly. The pump almost always remains off for many minutes once the gear is completely retracted. The gear was left in the up position for at least 5+ minutes at one point and we did not observe any restart of the pump. We did observe a quick on-off cycle of the pump perhaps 5 seconds after retraction during just one of 15-20 retraction tests performed, but again, normally the pump would shut off after the last cycle and remain off for many minutes during our testing. Everything seems normal compared to what I have observed when we did the annuals before except for the pump cycling off and on near the end of the main gear retraction cycle. We have studied the hydraulic and electrical schematics for the system and looks like there is a pressure limit switch that is responsible for stopping the pump motor when the pressure reaches approximately 1800 psi. This should occur after all the gear is retracted and against the physical stops. We are theorizing that this switch or the contactor that it operates could be faulty and prematurely stopping the pump prior to the gear being completely retracted. If the switch opened at a lower pressure for instance or cycled between opened and closed in a lower pressure range then it was supposed to we are thinking that the symptoms we are seeing would result. According to the maintenance manual the switch is supposed to close at 200 to 400 psi and open at 1800 +/- 100 psi. We have looked all over for anything impeding the main gear retraction and were not able to identify any hang-ups there. We have also verified that adequate 5606 is available in the reservoir of the pump. Again if anyone has some insights on my gear retract symptoms I would sure like to hear about it. If you believe our theory about the pressure limit switch being bad is unlikely and that it would be wiser to go down another path I would also like to hear about that too. My mechanic and I will be all over this tomorrow so if you know anything about this post what you know. - George |
#14
|
|||
|
|||
Saratoga Gear Retract Problem
I think that raising and lowering a rubber hose to blindly
service/verify the proper level in a power pack reservoir is really goofy. Not sure if that's how yours works or not, but on the newer models the hose was clipped to the side of the nose. Goofy. Ditto. Raise it, fill it, lower it, check it, raise it, add some more, lower it. Clip it back in place. Goofy. In the past, whenever I serviced an Aztruck pack, it would typically vent some on it's first or second (or third) flight, but it never appeared to be very much. The puddle seemed to be about two tablespoons full I would guess. Created a stain about 6" dia. I guess I would keep an eye on it to make sure that it isn't still venting, or if it does drip a little more, make sure that it stops after it decides it's at the proper level. Present course of action. Plane's leaving for a 4 day trip this weekend. It's topped off now and we'll see what it looks like when it comes back. Thanks as always. Jim |
#15
|
|||
|
|||
Saratoga Gear Retract Problem
I paid $550 for a replacement switch for my Seneca1 five years ago. Glad I
had it replaced then. Same part (mfg. by Consolidated Controls) "George Sconyers" wrote in message ... Sure hope my problem is the same as yours. I just ordered the $672 switch from Piper! Hopefully, my mechanic's discount he has setup with them will bring the price down 30%. Do you remember what you payed for the pressure limit switch (Piper part number 587-847)? -George "The Visitor" wrote in message ... I have a seneca 3. My problem started out like that, easy to sort of fly with. Then it got worse. Sometimes wouldn't at all retract, or just partially then pump would go off. We, flushed out and changed fluid, swaped up and down relays(they are the same), measured pump pressure, changed pump/motor, gear was in no way binding. The last thing checked was an over pressure limit switch that was going faulty and shutting the pump off. 2000 Saratoga? Mmmmm, nice. Our gear is probably similar in design?? Good Luck. John Yahoo! News wrote: During day one of my 2000 Saratoga's annual today my mechanic and I observed the following problem. If anyone has some experience with this or they have a mechanic that has experience with this I would love to hear about it: Here is a description of what we are observing: 1) Gear retraction is initiated with handle being placed into the gear up position 2) Nose gear and main gear unlock and start retraction 3) Gear Unsafe light illuminates simultaneously with gear unlocks 4) In about 1-2 seconds, nose gear completes retraction first (this is normal as far as what I have observed in the past both on my plane on jacks and on observing others from the ground departing from airports) 5) Main gear comes up part way but hesitates until nose gear completes retraction - again I believe this is normal 6) Main gear almost completes retraction in about 2 seconds after nose gear - a few inches from being completely retracted - this is where something has changed. 7) Pump Motor shuts off for approximately ¼ second 8) Pump Motor starts again for approximately ¼ second and gear moves up a little more (maybe ½ inch to 1 inch) 9) Pump Motor shuts off again and restarts again 3-5 times in the same pattern of quick off and ons before gear is completely retracted and pump motor remains off 10) Gear warning light extinguishes about the time or slightly before the pump motor shuts off for the last time This process is very repeatable. Only the number of quick off-on cycles of the pump varies slightly. The pump almost always remains off for many minutes once the gear is completely retracted. The gear was left in the up position for at least 5+ minutes at one point and we did not observe any restart of the pump. We did observe a quick on-off cycle of the pump perhaps 5 seconds after retraction during just one of 15-20 retraction tests performed, but again, normally the pump would shut off after the last cycle and remain off for many minutes during our testing. Everything seems normal compared to what I have observed when we did the annuals before except for the pump cycling off and on near the end of the main gear retraction cycle. We have studied the hydraulic and electrical schematics for the system and looks like there is a pressure limit switch that is responsible for stopping the pump motor when the pressure reaches approximately 1800 psi. This should occur after all the gear is retracted and against the physical stops. We are theorizing that this switch or the contactor that it operates could be faulty and prematurely stopping the pump prior to the gear being completely retracted. If the switch opened at a lower pressure for instance or cycled between opened and closed in a lower pressure range then it was supposed to we are thinking that the symptoms we are seeing would result. According to the maintenance manual the switch is supposed to close at 200 to 400 psi and open at 1800 +/- 100 psi. We have looked all over for anything impeding the main gear retraction and were not able to identify any hang-ups there. We have also verified that adequate 5606 is available in the reservoir of the pump. Again if anyone has some insights on my gear retract symptoms I would sure like to hear about it. If you believe our theory about the pressure limit switch being bad is unlikely and that it would be wiser to go down another path I would also like to hear about that too. My mechanic and I will be all over this tomorrow so if you know anything about this post what you know. - George |
#16
|
|||
|
|||
Saratoga Gear Retract Problem
The problem was indeed the pressure sensor switch. Gear retract time is now
3-4 seconds total and smooth. "Yahoo! News" wrote in message t... During day one of my 2000 Saratoga's annual today my mechanic and I observed the following problem. If anyone has some experience with this or they have a mechanic that has experience with this I would love to hear about it: Here is a description of what we are observing: 1) Gear retraction is initiated with handle being placed into the gear up position 2) Nose gear and main gear unlock and start retraction 3) Gear Unsafe light illuminates simultaneously with gear unlocks 4) In about 1-2 seconds, nose gear completes retraction first (this is normal as far as what I have observed in the past both on my plane on jacks and on observing others from the ground departing from airports) 5) Main gear comes up part way but hesitates until nose gear completes retraction - again I believe this is normal 6) Main gear almost completes retraction in about 2 seconds after nose gear - a few inches from being completely retracted - this is where something has changed. 7) Pump Motor shuts off for approximately ¼ second 8) Pump Motor starts again for approximately ¼ second and gear moves up a little more (maybe ½ inch to 1 inch) 9) Pump Motor shuts off again and restarts again 3-5 times in the same pattern of quick off and ons before gear is completely retracted and pump motor remains off 10) Gear warning light extinguishes about the time or slightly before the pump motor shuts off for the last time This process is very repeatable. Only the number of quick off-on cycles of the pump varies slightly. The pump almost always remains off for many minutes once the gear is completely retracted. The gear was left in the up position for at least 5+ minutes at one point and we did not observe any restart of the pump. We did observe a quick on-off cycle of the pump perhaps 5 seconds after retraction during just one of 15-20 retraction tests performed, but again, normally the pump would shut off after the last cycle and remain off for many minutes during our testing. Everything seems normal compared to what I have observed when we did the annuals before except for the pump cycling off and on near the end of the main gear retraction cycle. We have studied the hydraulic and electrical schematics for the system and looks like there is a pressure limit switch that is responsible for stopping the pump motor when the pressure reaches approximately 1800 psi. This should occur after all the gear is retracted and against the physical stops. We are theorizing that this switch or the contactor that it operates could be faulty and prematurely stopping the pump prior to the gear being completely retracted. If the switch opened at a lower pressure for instance or cycled between opened and closed in a lower pressure range then it was supposed to we are thinking that the symptoms we are seeing would result. According to the maintenance manual the switch is supposed to close at 200 to 400 psi and open at 1800 +/- 100 psi. We have looked all over for anything impeding the main gear retraction and were not able to identify any hang-ups there. We have also verified that adequate 5606 is available in the reservoir of the pump. Again if anyone has some insights on my gear retract symptoms I would sure like to hear about it. If you believe our theory about the pressure limit switch being bad is unlikely and that it would be wiser to go down another path I would also like to hear about that too. My mechanic and I will be all over this tomorrow so if you know anything about this post what you know. - George |
#17
|
|||
|
|||
Saratoga Gear Retract Problem
On Tue, 29 Nov 2005 13:16:25 -0600, "Jim Burns"
wrote: Goofy. Ditto. Raise it, fill it, lower it, check it, raise it, add some more, lower it. Clip it back in place. Goofy. The only one I've come across that is goofier was the old Navajos. The powerpack fill pipe was hooked to the side of the brake reservoir. You over-filled the brake reservoir until it ran into the power pack. Another goofy thing about this system (which carried through on the newer models) was the screw-down Thermos-type combination stopper/dipstick. Was mounted under a little flapper door on the top of the nose. The "rubber" on the stopper was semi-incompatible with 5606, and usually leaked. Depending on the amount of precipitation present, water would run under the door, around the stopper and into the reservoir. This wasn't typically a problem until winter, when the globs of water would freeze in the lines, either rendering some/all of the brake system inop, or trapping pressure in the lines-locking some/all of the brakes. Had most of the line guys trained to crack the bleeders and shove the !@$% thing into the hangar to thaw out when it happened when I wasn't around. In the past, whenever I serviced an Aztruck pack, it would typically vent some on it's first or second (or third) flight, but it never appeared to be very much. The puddle seemed to be about two tablespoons full I would guess. Created a stain about 6" dia. Sounds familiar. I guess I would keep an eye on it to make sure that it isn't still venting, or if it does drip a little more, make sure that it stops after it decides it's at the proper level. Present course of action. Plane's leaving for a 4 day trip this weekend. It's topped off now and we'll see what it looks like when it comes back. Good deal. Thanks as always. My pleasure. TC |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Gear Warning | Gadget Guy | Soaring | 118 | November 30th 05 10:43 PM |
Aluminum vs Fiberglass landing gear - Pro's and cons. | Bart Hull | Home Built | 1 | November 24th 03 02:46 PM |
Aluminum vs Fiberglass landing gear - Pro's and cons. | Bart Hull | Home Built | 2 | November 24th 03 05:23 AM |
Aluminum vs Fiberglass landing gear - Pro's and cons. | Bart Hull | Home Built | 0 | November 24th 03 03:52 AM |
Aluminum vs Fiberglass landing gear - Pro's and cons. | Bart D. Hull | Home Built | 0 | November 22nd 03 06:24 AM |