If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
50 degrees rich of peak
Ok. Just want to see if I have this correct. When leaning using an EGT
gauge the 172R POH says to lean untill the EGT needle peaks then enrich to 50 degrees F rich of peak EGT. So the EGT temperature will be 50 degrees less than the peak reading. Right? |
#2
|
|||
|
|||
Right. Your understanding of what 50 degrees rich of peak means is
correct. Whether that's a good way to operate the engine is highly debatable. Michael |
#3
|
|||
|
|||
"Michael" wrote in message ups.com... Right. Your understanding of what 50 degrees rich of peak means is correct. Whether that's a good way to operate the engine is highly debatable. The actual and extensive data shows it's about the worst place you can operate. That's in terms of both CHT and cylinder pressures. |
#4
|
|||
|
|||
lardsoup wrote:
So the EGT temperature will be 50 degrees less than the peak reading. Right? Slowly roll out the mixture lever watching the EGT gauge. When the temperature on the EGT gauge peaks and begins to fall, roll in the mixture lever until the temperature peaks, then keep rolling it inward until the temperature needle falls 50 degrees below (or less than) the peak temperature you witnessed. -- Peter ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups ----= East and West-Coast Server Farms - Total Privacy via Encryption =---- |
#5
|
|||
|
|||
Depends on if you want best power or best range. 50 degrees is for best
range, and 75 for best power if you don't want to crisp your valves. Think of the heat in the valve section....excess fuel cools the valves and that is what the EGT is doing for you. |
#6
|
|||
|
|||
selway,
You might want to read Deakin's articles on engine ops in AVweb. Crisping or burning the valves is an oft repeated, but untrue statement. It is without any data to support it. All the best, Rick |
#7
|
|||
|
|||
excess fuel cools the valves
and that is what the EGT is doing for you. Uhm, actually, no. Excess fuel is slowing the burn front, which in turn cools down the burn process, which in turn reduces EGT. Now, lean of peak, you have excess air cooling the exhaust gas. -- Thomas Borchert (EDDH) |
#8
|
|||
|
|||
On Sat, 25 Jun 2005 13:35:35 +0200, Thomas Borchert
wrote: Uhm, actually, no. Excess fuel is slowing the burn front, which in turn cools down the burn process, which in turn reduces EGT. Now, lean of peak, you have excess air cooling the exhaust gas. Close, but not quite according to Deakin. The excess fuel causes the mixture to burn more slowly, but what this does is delay the Peak Pressure Point from occuring too close to the piston being at Top Dead Center. Either side of the precisely correct fuel/air mixture and the combustion process occurs more slowly, but the actual combustion process (the flame inside the combustion chamber) is not much less hot. The PPP has to occur with the piston at around 12 degree ATDC (After Top Dead Center) in order for the maximum push on the piston with minimum strain on the bearings and connecting rod. The closer to TDC the piston is when the PPP occurs, the more pressure and strain and more HEAT is produced. The PPP doesn't happen instantly. The mixture has to be ignited a certain number of degrees before TDC so that by the time the piston is at the proper position, the combustion has reached it's maximum pressure. For most fixed timing engines, that setting is around 26 to 28 degrees BTDC. So the magnetos are set there. But this is a setting that requires full rich in order for the PPP to occur at 12 degrees ATDC. If the mixture is leaned for takeoff while the airplane is at or near sea level, the combustion process speeds up. Because the combustion process speeds up, the PPP begins to occur closer to TDC, which is a bad thing. So the additional fuel, or overly rich mixture, doesn't produce a cooler flame front, it simply slows down the combustion so that it can occur at the proper place. This produces acceptible cylinderhead temperatures. Leaning past the stoichiometrically correct mixture also slows down the burning process (which keeps the engine cool), but this time, you're using a lot less fuel while doing it. And the above is just for takeoff. When cruising you usually slow the engine down. Slowing the engine down brings the PPP very close to TDC. So you have to either cruise rich or very lean in order for the PPP to be where it needs to be to prevent long term damage to the engine. Corky Scott |
#9
|
|||
|
|||
Corky,
you got it right - I was quoting from memory. My key point was supposed to be that there is no "vaporisation cooling" by excess fuel at rich mixtures. -- Thomas Borchert (EDDH) |
#10
|
|||
|
|||
Lardsoup,
go to www.avweb.com and search for columns by John Deakin on engine management. Read them all. They will answer your question - and tell you much more that's really good to know. Fun to read, too. -- Thomas Borchert (EDDH) |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Headwinds, always | Paul kgyy | Piloting | 36 | June 9th 05 01:05 AM |
Lycoming's views on best economy settings | [email protected] | Piloting | 37 | July 8th 04 04:00 PM |
Constant speed props | GE | Piloting | 68 | July 3rd 04 04:08 AM |
Lean of Peak Test Flight | Roger Long | Piloting | 0 | April 22nd 04 10:13 AM |
Thanks for the Spins Rich | David B. Cole | Aerobatics | 17 | October 26th 03 08:37 AM |