If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
When do controls return to neutral?
In a typical small GA aircraft, do the controls have a natural
tendency to return exactly to their neutral positions when you aren't holding them and when you are on the ground? Do they have a tendency to return to exactly neutral in flight if you release them in level flight? The reason I ask is that sometimes the controls I use in simulation don't snap back to exactly neutral when I release them, and I'm trying to determine whether this is more realistic or less realistic with respect to a real aircaft. I suppose it depends on the aircraft, but what is the usual case? And if you happen to know how it behaves specifically on a Baron or an A36, I'd be particularly interested to know that. -- Transpose mxsmanic and gmail to reach me by e-mail. |
#2
|
|||
|
|||
When do controls return to neutral?
Usually, in a non-aerobatic plane, ailerons and rudder will return
close to neutral. Elevator will go to its trim position. Several of the classic planes I've flow do not have this tendency, so it really can go either way, but most planes today are designed to be easy to fly. -Robert, CFII Mxsmanic wrote: In a typical small GA aircraft, do the controls have a natural tendency to return exactly to their neutral positions when you aren't holding them and when you are on the ground? Do they have a tendency to return to exactly neutral in flight if you release them in level flight? The reason I ask is that sometimes the controls I use in simulation don't snap back to exactly neutral when I release them, and I'm trying to determine whether this is more realistic or less realistic with respect to a real aircaft. I suppose it depends on the aircraft, but what is the usual case? And if you happen to know how it behaves specifically on a Baron or an A36, I'd be particularly interested to know that. -- Transpose mxsmanic and gmail to reach me by e-mail. |
#3
|
|||
|
|||
When do controls return to neutral?
Robert M. Gary writes:
Usually, in a non-aerobatic plane, ailerons and rudder will return close to neutral. Elevator will go to its trim position. Several of the classic planes I've flow do not have this tendency, so it really can go either way, but most planes today are designed to be easy to fly. Is there any tendency for the control surfaces to set in positions slightly off neutral? For example, if you have to use rudder a lot to counter torque on every flight, is there any tendency of the rudder over time to stay a little bit on that side? My joystick seems to do this, very slightly, and since it is mechanical like control surfaces, I wonder if things like a rudder might do the same. Not a very big deflection, of course, but enough that you might notice it in otherwise perfect level flight (although with the engine running, I suppose there would always be torque acting more strongly in the opposite direction, so how would you know?). -- Transpose mxsmanic and gmail to reach me by e-mail. |
#4
|
|||
|
|||
When do controls return to neutral?
Mxsmanic wrote: Robert M. Gary writes: Is there any tendency for the control surfaces to set in positions slightly off neutral? For example, if you have to use rudder a lot to counter torque on every flight, is there any tendency of the rudder over time to stay a little bit on that side? Usage doesn't cause this. However with age sometimes a plane doesn't fly as straight as it used to. If the plane isn't flying straight (i.e. the ball isn't in the middle when you take your feet off the rudders) you can adjust it. On my plane there is a bolt that adjust the throw but a lot of planes just have metal trim tabs. What you are asking about is referred to as "rigging" and is one of the great dark arts in aviation. The manual will tell you how to do it but only a few really good A&P's can really get your bird (especially a more complex one like mine) to fly straight. Right now my plane slips to the right about 1/2 ball when I put the gear out. Not sure why, it didn't used to. With rigging you usually want to seek out an A&P familiar with your plane (especially if you have rigging wires, don't ever let a generic A&P touch rigging wires if you fly a classic). -Robert |
#5
|
|||
|
|||
When do controls return to neutral?
In article . com,
"Robert M. Gary" wrote: Mxsmanic wrote: Robert M. Gary writes: Is there any tendency for the control surfaces to set in positions slightly off neutral? For example, if you have to use rudder a lot to counter torque on every flight, is there any tendency of the rudder over time to stay a little bit on that side? Usage doesn't cause this. However with age sometimes a plane doesn't fly as straight as it used to. If the plane isn't flying straight (i.e. the ball isn't in the middle when you take your feet off the rudders) you can adjust it. On my plane there is a bolt that adjust the throw but a lot of planes just have metal trim tabs. What you are asking about is referred to as "rigging" and is one of the great dark arts in aviation. The manual will tell you how to do it but only a few really good A&P's can really get your bird (especially a more complex one like mine) to fly straight. Right now my plane slips to the right about 1/2 ball when I put the gear out. Not sure why, it didn't used to. With rigging you usually want to seek out an A&P familiar with your plane (especially if you have rigging wires, don't ever let a generic A&P touch rigging wires if you fly a classic). Aircraft without adjustable rudder trim have a ground adjustable piece of metal (a "tab") attached to the trailing edge of the rudder. This tab is bent at an angle to the plane of the rudder so that the aircraft will fly with no yaw (theoretically) at "cruise" speed. Change the airspeed and the aircraft will yaw right or left. |
#6
|
|||
|
|||
When do controls return to neutral?
If it slips with gear extended, probably a door is not
aligned and is acting as a rudder. "Robert M. Gary" wrote in message ups.com... | | Mxsmanic wrote: | Robert M. Gary writes: | Is there any tendency for the control surfaces to set in positions | slightly off neutral? For example, if you have to use rudder a lot to | counter torque on every flight, is there any tendency of the rudder | over time to stay a little bit on that side? | | Usage doesn't cause this. However with age sometimes a plane doesn't | fly as straight as it used to. If the plane isn't flying straight (i.e. | the ball isn't in the middle when you take your feet off the rudders) | you can adjust it. On my plane there is a bolt that adjust the throw | but a lot of planes just have metal trim tabs. | What you are asking about is referred to as "rigging" and is one of the | great dark arts in aviation. The manual will tell you how to do it but | only a few really good A&P's can really get your bird (especially a | more complex one like mine) to fly straight. Right now my plane slips | to the right about 1/2 ball when I put the gear out. Not sure why, it | didn't used to. With rigging you usually want to seek out an A&P | familiar with your plane (especially if you have rigging wires, don't | ever let a generic A&P touch rigging wires if you fly a classic). | -Robert | |
#7
|
|||
|
|||
When do controls return to neutral?
Yeah - essentially what you're talking about is the fundamental point
of trim devices on modern aircraft. Neutral position is a bit of a 'bad' term here, because unlike a simulator's joystick, there is no defined "Central" location for a yoke. Yes, of course wing's level is fairly 'central', but for rudder and elevator, there is quite a bit of play as to where 'neutral' is (where neutral is fundamentally defined as the point at which the controls naturally go when you apply no force to them). The "neutral point" described above is is set by your trimming mechanisms. In my PA-28-140, I have 3 mechanisms to trim the plane - I have the pitch trim handle, I have a rudder trim mechanism (which actually just manipulates the pedals) and I have the ability to control my fuel burn on one side or the other to trim for roll. This is one of the areas where flying a real plane is fundamentally different than flying with a computer joystick. with a computer joystick, there is always a "center point", and trim is simulated by having the aircraft turn to one side or the other while the joystick is in the center point. In a real aircraft, the physical point where the control's center themselves varies based on trim, but AOA effect of having the controls at any given point is usually the same. (I.E, having the yoke 3" out from the panel will try to move the aircraft towards the same AOA, regardless if this is 'trimmed as neutral' and I can take my hand off, or the aircraft is trimmed for another speed and the yoke is pushing against my hand). Also note that this is all very delibrate- The anti-servo tab on a PA-28's tail is explicitly designed to provide this very type of tactile feedback - that's its whole point. On Nov 7, 3:18 pm, Mxsmanic wrote: In a typical small GA aircraft, do the controls have a natural tendency to return exactly to their neutral positions when you aren't holding them and when you are on the ground? Do they have a tendency to return to exactly neutral in flight if you release them in level flight? The reason I ask is that sometimes the controls I use in simulation don't snap back to exactly neutral when I release them, and I'm trying to determine whether this is more realistic or less realistic with respect to a real aircaft. I suppose it depends on the aircraft, but what is the usual case? And if you happen to know how it behaves specifically on a Baron or an A36, I'd be particularly interested to know that. -- Transpose mxsmanic and gmail to reach me by e-mail. |
#8
|
|||
|
|||
When do controls return to neutral?
EridanMan writes:
Neutral position is a bit of a 'bad' term here, because unlike a simulator's joystick, there is no defined "Central" location for a yoke. Yes, of course wing's level is fairly 'central', but for rudder and elevator, there is quite a bit of play as to where 'neutral' is (where neutral is fundamentally defined as the point at which the controls naturally go when you apply no force to them). I was kind of thinking along those lines. So I presume that I need not fret about not necessarily having an obvious neutral position in the sim. If I understand correctly, in a real aircraft, it all just depends on circumstances, and you don't have to know or care about any "exact" neutral (?). The "neutral point" described above is is set by your trimming mechanisms. In my PA-28-140, I have 3 mechanisms to trim the plane - I have the pitch trim handle, I have a rudder trim mechanism (which actually just manipulates the pedals) and I have the ability to control my fuel burn on one side or the other to trim for roll. Do you have a marked "zero point" for the trim, or do you just trim until it feels right for the circumstances, and then trim again the next time as required, without worrying about whether the trim is truly "zero" or not? This is one of the areas where flying a real plane is fundamentally different than flying with a computer joystick. with a computer joystick, there is always a "center point", and trim is simulated by having the aircraft turn to one side or the other while the joystick is in the center point. In a real aircraft, the physical point where the control's center themselves varies based on trim, but AOA effect of having the controls at any given point is usually the same. (I.E, having the yoke 3" out from the panel will try to move the aircraft towards the same AOA, regardless if this is 'trimmed as neutral' and I can take my hand off, or the aircraft is trimmed for another speed and the yoke is pushing against my hand). So in a real aircraft, a different trim position also represents a different yoke position? That seems logical. I wonder how fly-by-wire aircraft handle this. Also note that this is all very delibrate- The anti-servo tab on a PA-28's tail is explicitly designed to provide this very type of tactile feedback - that's its whole point. I read that a drawback to Cirrus aircraft is that they use springs for feedback, so it's hard to tell where the control surfaces actually are. -- Transpose mxsmanic and gmail to reach me by e-mail. |
#9
|
|||
|
|||
When do controls return to neutral?
In article ,
Mxsmanic wrote: Do you have a marked "zero point" for the trim, or do you just trim until it feels right for the circumstances, and then trim again the next time as required, without worrying about whether the trim is truly "zero" or not? There are marks/indicators, however they are mechanical pointers which are subject to deviation. In actuallity, yes, you move the trim control until the pressure is neutralized (in the case of elevator for the the speed and power setting, and for rudder until the yaw ball is centered). |
#10
|
|||
|
|||
When do controls return to neutral?
"Mxsmanic" wrote in message ... Do you have a marked "zero point" for the trim, or do you just trim until it feels right for the circumstances, and then trim again the next time as required, without worrying about whether the trim is truly "zero" or not? Most aircraft have an index mark for "Take-Off" trim position. I'm pretty damn sure that MSFS shows this index mark as well. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Return from AirVenture | john smith | Piloting | 7 | August 3rd 06 05:35 PM |
Fly-By-Wire Flight Controls | Charles Talleyrand | Piloting | 52 | December 28th 05 10:27 PM |
Parachute fails to save SR-22 | Capt.Doug | Piloting | 72 | February 10th 05 05:14 AM |
for mr. pethukov ( Bush May Announce Return To Moon At Kitty Hawk) | captain! | Military Aviation | 6 | October 30th 03 05:11 PM |
Real World Specs for FS 2004 | Paul H. | Simulators | 16 | August 18th 03 09:25 AM |