![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
Aircoupe Alon A2 with C90 engine with two props, one 48" pitch and the
other 52". It doesn't make the static runup RPM minimums with either one, for instance the 48" prop should be 2225 to 2325 rpm, I averaged out to 2162 rpm. Likewise the 52" prop falls short 100 rpm or more. Three years ago when I checked the tachometer, it read a little slow--maybe 10-20 rpm at speed, that is it would indicate 2300 and the electronically measured rpm would be 2310 or so. Assuming that's still true, what would cause the engine to not make minimum rpm? Where should I start troubleshooting? |
#2
|
|||
|
|||
![]()
I would start with the Tach.
Tony -- Tony Roberts PP-ASEL VFR OTT Night Cessna 172H C-GICE Where should I start troubleshooting? |
#3
|
|||
|
|||
![]()
In rec.aviation.owning Bob Fry wrote:
: Three years ago when I checked the tachometer, it read a little : slow--maybe 10-20 rpm at speed, that is it would indicate 2300 and the : electronically measured rpm would be 2310 or so. Assuming that's : still true, what would cause the engine to not make minimum rpm? : Where should I start troubleshooting? In rough order of liklihood - Tach - Mixture (Here at 2100 MSL, often too high DA to get full RPM in the summer) - Timing - Air filter - Muffler blockage - Compression - Ignition (plugs) - Ignition (others... unlikely: mag internal timing (egap), wires) -- ************************************************** *********************** * Cory Papenfuss * * Electrical Engineering candidate Ph.D. graduate student * * Virginia Polytechnic Institute and State University * ************************************************** *********************** |
#4
|
|||
|
|||
![]()
tony roberts wrote:
I would start with the Tach. Good suggestion. There is a program available for a Palm Pilot that indicates RPM using its built in microphone. |
#5
|
|||
|
|||
![]()
Borrow a optical tach from a A&P.
Dynamically balance the prop(s) Cory hit upon a good idea ie muffler blockage. You could have a blown baffle or collapsed tube in your muffler. Jim |
#6
|
|||
|
|||
![]()
I just went thru this with my Beech Sundowner. It was not making
minimum static rpm and would not go over 2500 at 7500 ft leaned. Everything checked out, then pulled the prop and had the prop shop check it and it failed. Not enough metal to overhaul it and it surprised me cause it looked good. Put a new prop on it and now getting 125 rpm more at static. Bob Fry wrote: Aircoupe Alon A2 with C90 engine with two props, one 48" pitch and the other 52". It doesn't make the static runup RPM minimums with either one, for instance the 48" prop should be 2225 to 2325 rpm, I averaged out to 2162 rpm. Likewise the 52" prop falls short 100 rpm or more. Three years ago when I checked the tachometer, it read a little slow--maybe 10-20 rpm at speed, that is it would indicate 2300 and the electronically measured rpm would be 2310 or so. Assuming that's still true, what would cause the engine to not make minimum rpm? Where should I start troubleshooting? |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Homebuilt Aircraft Frequently Asked Questions List (FAQ) | Ron Wanttaja | Home Built | 0 | September 2nd 04 05:15 AM |
Engines and Reliability | Dylan Smith | Piloting | 13 | June 30th 04 03:27 PM |
Corky's engine choice | Corky Scott | Home Built | 39 | August 8th 03 04:29 AM |