If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
engine monitors
I am considering installing an engine monitor in my Skyhawk . . . and have
narrowed the search to these two selections: Gem610 and JPI EDM-700 Any pireps, recommendations, anecdotes, or other feedback? Thanks in advance . . . www.Rosspilot.com |
#2
|
|||
|
|||
I have EDM 700's in my Extra and Baron, and they work great. Aviation
Consumer had a review on these, and based upon their recommendations I went with the EDM. You can check out their back issues online. |
#3
|
|||
|
|||
I was looking into this also. If you do a google search, you'll find a lot
of information. "Rosspilot" wrote in message ... I am considering installing an engine monitor in my Skyhawk . . . and have narrowed the search to these two selections: Gem610 and JPI EDM-700 Any pireps, recommendations, anecdotes, or other feedback? Thanks in advance . . . www.Rosspilot.com |
#4
|
|||
|
|||
EDM 700.
You can download the data after each flight and plot it using a spreadsheet. |
#5
|
|||
|
|||
Although I'd probably pick them, I just heard that EDM changed their data
download format to restrict its usage to only their proprietary software. They wanted to keep one from using others, such as "EGT Trends". Anybody else heard that or know why? EDM 700. You can download the data after each flight and plot it using a spreadsheet. |
#6
|
|||
|
|||
JPI EDM-700
I have this in my Skyhawk and love it. |
#7
|
|||
|
|||
Not exactly. You can still down load it and look at it with a spread
sheet, however they would be very happy to sell your their tracking tool. |
#8
|
|||
|
|||
EDM 700 works great for me. Just upgraded it with fuel flow - very nice.
Rosspilot wrote: I am considering installing an engine monitor in my Skyhawk . . . and have narrowed the search to these two selections: Gem610 and JPI EDM-700 Any pireps, recommendations, anecdotes, or other feedback? Thanks in advance . . . www.Rosspilot.com |
#9
|
|||
|
|||
"Rosspilot" wrote in message ... I am considering installing an engine monitor in my Skyhawk . . . and have narrowed the search to these two selections: Gem610 and JPI EDM-700 I looked at both of these and went with the JPI due to it's far better (more better?) usability and functionality. -- Matt --------------------- Matthew W. Barrow Site-Fill Homes, LLC. Montrose, CO |
#10
|
|||
|
|||
In article ,
Gene Kearns wrote: Had a EDM-700 in my last A/C... I'll be installing a UBG-16 in my current aircraft, this spring.... Why? -- Ben Jackson http://www.ben.com/ |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
ROP masking of engine problems | Roger Long | Owning | 4 | September 27th 04 07:36 PM |
Proposals for air breathing hypersonic craft. I | Robert Clark | Military Aviation | 2 | May 26th 04 06:42 PM |
My Engine Fire!! | [email protected] | Owning | 1 | March 31st 04 01:41 PM |
Car engine FAA certified for airplane use | Cy Galley | Home Built | 10 | February 6th 04 03:03 PM |
Corky's engine choice | Corky Scott | Home Built | 39 | August 8th 03 04:29 AM |