If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Things I Have Learned As First Time Buyer/Owner (long)
Well I learned when doing a pre buy be sure you take it to the avionics shop
and have all the avionics and instruments checked out before you buy my mistake only thing that was not checked at the pre buy waqs the avionics. I was more concerned about the engine and airframe. I had the transponder checked about 3 weeks ago all tested ok Well today while flying in class C airspace (KPDX) the transponder went out the tower did not like that very much and was told to depart their airspace ASAP. I landed at the nearest airport and went to an avionics shop what do you know the transponder stopped receiving and transmitting at it happens things fail. The next airplane I buy ill have the avionics checked out in the pre buy defiantly. Now all my avionics and instruments are now new and or checked out and working 100% correctly. I have been told that I should contact my local FSDO about the A&P-IA that signed things off as things were not done correctly and could have caused major problems. Not sure I want to do that and not sure what I should do. The last avionics shop told me my ADF was bad I sent it out to a shop of my choice it checked out ok no repairs needed. It was my ADF antenna that was the problem a little scotch bright took care of that. Just a little corrosion on the wire antenna connection. They also told me my Glide Slope Was Not fully deflecting and my VOR was off 8 degrees and needed to be replaced. Retested by another shop and well it is well within factory limits humm. They set my altimeter settings wrong + 110' on the ground yeiks. Said my marker beacon receiver was bad and entire audio panel needed replaced with a new one. Nope it was a $3.00 diode. Now I am wondering if they over pressurized my pito system and blew my airspeed indicator diaphragm to try and sell me a new one of them also who knows. Well 5 hours at the avionics shop today and a rebuilt Transponder, Repaired 3LMB and a new sticker in the log book showing how the problems that the last shop goofed up on. Now all is fixed and what a joy to fly every things works very very very well. I am glad that my transponder went out on me today and forced me to land at a larger airport to get it fixed. I was kinda questioning in the back of my mind the business ethics of the last avionics shop, after the ADF came back from the repair house ok with no problems. I think I will let it go as a $600.00 lesson learned and steer business away from that avionics shop that goofed things up and refer to the shop I went to today at leased they have proper equipment to do it right. They had equipment that looked like it needed a manual larger than a Linux manual to operate. I will not mention names until I confront the last avionics shop with my paperwork showing them that items that they said were defective were not ill see what they will do about the diagnostic time they charged me. Lessons learned: Don't ignore the avionics on a pre buy even if there is not an avionics shop at the airport you buy it at take it to one get it checked worth the $300.00 in labor you may save you a few thousand. Don't trust shops that tell you it cannot be fixed and you must replace it and try and sell you a entire new panel for $10,000 get a second opinion it may save you a headache and a bunch of money. Only go to shops that have modern equipment to do the job right ask to see their equipment and library you may see binders of schematics that's a good if they will show you bad if they don't have it, You may see a few newer turbine aircraft in their hanger and higher rates (+$20.00 an hour more than others but modern $30,000+ test equipment has to be paid for some how) You may want to pay now or you will be paying pay later. I am an electronics engineer by trade I am not comfortable paying $80.00 to have a $3.00 part replaced but way better than paying $1,800 for a new audio panel. Biggest lesson learned is who not to deal with well worth the $600 I had to spent today to learn that. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
AOPA Stall/Spin Study -- Stowell's Review (8,000 words) | Rich Stowell | Aerobatics | 28 | January 2nd 09 02:26 PM |
FAA Application -- kinds of time | Gary Drescher | Instrument Flight Rules | 5 | November 23rd 04 02:33 PM |
the complete minute by minute timeline on 911 | Krztalizer | Military Aviation | 27 | January 27th 04 04:35 PM |
Homebuilt Aircraft Frequently Asked Questions (FAQ) | Ron Wanttaja | Home Built | 4 | August 7th 03 05:12 AM |
Homebuilt Aircraft Frequently-Asked Questions (FAQ) | Ron Wanttaja | Home Built | 0 | July 4th 03 04:50 PM |