If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#41
|
|||
|
|||
Blueskies wrote:
wrote in message ... On Sun, 09 Jan 2005 13:09:44 GMT, "Blueskies" The VAST majority are bright zinc plated. You guys are probably right - zinc is it; same as galvanized, right? Yep, galvanized means zinc coated (by electroplating). A lot of car body parts are nowadays too, they figured out how to make paint stick to the zinc coating, look nice, and cost low enough to still turn a profit. |
#42
|
|||
|
|||
Blueskies wrote:
"VideoFlyer" wrote in message ... Lowes and Home Dee-pot are *not* hardware stores. . . ;-) That's true.....but they're the closest thing to a hardware store that I have seen for many years. Where did all the GOOD hardware stores go. I went into Menards a few weeks ago looking for a 3 inch V-belt pulley for an air compressor. The person who waited on me had no idea what a pulley was. He started showing me ratchet cable "pullers"....like a "come-along." Last month I went into the same store and asked if they carried tap and die sets. Again...the person who waited on me didn't have a clue as to what I was talking about. snip I must sound like an old f*rt reminiscing about the good old days. I am a YOUNG 47 year old male. We have a really good Ace Hardware store here. I know they are struggling with Menards, The Home Depot, and Lowes within 4 miles. I use them every chance I get... Ace is pretty good, for example they carry number and letter size drill bits. I've never found that at Home Depot or Lowes, just the fraction sizes from about 1/16 to 1". The help you get from staff depends. At a Lowe's once I got good help from an older guy, who seemed to have actually made stuff with his hands and knew what I was talking about for moderately obscure tools (hand chuck). Not knowing what a tap and die set is? That's pretty bad, hopefully you caught one dumb guy on a bad day with that one. While we're ranting, I went to school for mechanical engineering. A lot of the people seemed to be in it because their high school guidance counselors told them they were good at math and science. Smart people, just a different kind of smart. I got into it because I thought it was neat the way stuff worked, but I had that in common with less than half of the guys. I don't work in that field now though, so it's just a pet theory of mine. Maybe Ron W. could weigh in on this one? [PS I'm a young 30, right now is the good old days] |
#43
|
|||
|
|||
"ChuckSlusarczyk" wrote in message ... In article , John Ammeter says... I've been shopping at the same Ace Hardware for well over 25 years. They know me by name and the owner has invited me to his Christmas Party.... Of course, with what I've spent there over the years, I probably have sent his kids to college twice over... John I've been waiting and waiting for some one to say what a "fender washer " is and no one yet has given the right answer! I can't wait anymore...A "fender washer" is the guy at the car wash that washes fenders,just like the tire washer ,door washer ,window washer etc...They are specialists at the better car washes. Besides this group is getting way to serious LOL!!! See ya Chuck (former fender washer) S I guess you missed it... A little guy name Jose' who works down at my local car wash. He's not tall enough to wash the top of the car, just the fenders. carl mciver wrote: "N:dlzc D:aol T:com (dlzc)" N: dlzc1 D:cox wrote in message news:rZWDd.23751$CH5.11854@fed1read01... | Dear alanh_27: | | wrote in message | ups.com... | what is a fender washer? in which situation is it used? | | Just to add a little to John Kunkel's response... | They also help distribute loading, when the bolted joint is into/includes | sheet metal. Serves to stiffen up the bolted area. | | David A. Smith Sort of. Usually not very strong, so they tend to sink a lot if you torque them down to a reasonable amount. I've brazed a smaller washer on top of a fender washer to stiffen one up, just stacking them only goes so far. Actually, I needed it to remove and replace some bearings from the front axle of my 4x4 truck. Had a 5/8" allthread going the length of the axle and you couldn't get washers the right diameter with a 5/8" hole in it. Lots of wrenching going on that day! |
#44
|
|||
|
|||
On Tue, 11 Jan 2005 00:54:31 -0600, Jim Carriere
wrote: While we're ranting, I went to school for mechanical engineering. A lot of the people seemed to be in it because their high school guidance counselors told them they were good at math and science. Smart people, just a different kind of smart. I got into it because I thought it was neat the way stuff worked, but I had that in common with less than half of the guys. I don't work in that field now though, so it's just a pet theory of mine. Maybe Ron W. could weigh in on this one? I got into engineering because I wanted to design stuff that would actually *do* things. Flash lights, make weird sounds, etc. I used to disassemble transistor radios and make strange little oscillators from the parts...one transistor, the output transformer, one resistor (preferably variable), and the speaker. Used to experiment for hours, finding out what a capacitor would do here, rigging up a light-dependent resistor for the pitch control, etc. Knew a guy in school who absolutely hated high-pitched sounds, so a built a fixed-frequency oscillator into a small candy box and arranged to hang around him for a while. Funny, how things turn out. I got my EE degree specializing in high-tension power lines, but was an ROTC type and went into the Air Force. Which completely ignored my educational background and assigned me as a sensor specialist for an early warning satellite. Post-Air Force, I worked as a test engineer for a bit then ended up as a Systems Engineer. Other than a two-year stint managing a set of RF design engineers at a dot-com, I've never even come close to using my degree.... Ron Wanttaja |
#45
|
|||
|
|||
In article , Blueskies says...
I guess you missed it... A little guy name Jose' who works down at my local car wash. He's not tall enough to wash the top of the car, just the fenders. Guess I did,at least the group hasn't lost all it's humor :-) Chuck S you can lead a horse to water ...but a pencil must be pointed . |
#46
|
|||
|
|||
Ron Wanttaja wrote:
I got into engineering because I wanted to design stuff that would actually *do* ... Funny, how things turn out. I got my EE degree specializing in high-tension power lines, but was an ROTC type and went into the Air Force. Which completely ignored my educational background and assigned me as a sensor specialist for an early warning satellite. Post-Air Force, I worked as a test engineer for a bit then ended up as a Systems Engineer. Other than a two-year stint managing a set of RF design engineers at a dot-com, I've never even come close to using my degree.... Oh... for some reason I figured you currently worked in the field, that's why I said maybe you could offer some insight about hands on vs book smart people in technical fields. Funny how things turn out, as you say. |
#47
|
|||
|
|||
And you can lead a horticulture
but you cannot make her think. Jim Chuck S you can lead a horse to water ...but a pencil must be pointed . |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Plastic fender? | Steve Thomas | Home Built | 0 | August 28th 03 04:36 PM |