If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Mounting a turn coordinator on the tail?
(Things are so slow in this group at the moment, I thought I'd post
this to get your input on something I've been mulling over...) If you put a plane into a skidding left turn (wings level) with left rudder, the ball on the panel goes to the right. However, I've been trying to work out what would happen to the ball if it was mounted on the tail. The rudder is pushing the tail of the plane to the right, so I think the ball would go to the left. Can anyone confirm this? Tim. |
#2
|
|||
|
|||
Mounting a turn coordinator on the tail?
I don't think so. My understanding is the ball rests in a slightly
curved tube, arranged so that gravity tends to center it. Centrifugal force tries to move it to the outside of the skid, up the curved tube. Neither of these forces depends on where you mount the turn coordinator. Tim Auckland wrote: (Things are so slow in this group at the moment, I thought I'd post this to get your input on something I've been mulling over...) If you put a plane into a skidding left turn (wings level) with left rudder, the ball on the panel goes to the right. However, I've been trying to work out what would happen to the ball if it was mounted on the tail. The rudder is pushing the tail of the plane to the right, so I think the ball would go to the left. Can anyone confirm this? Tim. |
#3
|
|||
|
|||
Mounting a turn coordinator on the tail?
Stubby,
Thanks, I think I've got it now. As the turn is initiated, the tail has to go right (this is what causes the plane to turn) and my guess is that the ball initially goes very slightly left. However, once a constant-radius turn has been achieved, the ball will be on the right (outside) of the turn. Tim. On Sat, 29 Jul 2006 18:28:28 -0400, Stubby wrote: I don't think so. My understanding is the ball rests in a slightly curved tube, arranged so that gravity tends to center it. Centrifugal force tries to move it to the outside of the skid, up the curved tube. Neither of these forces depends on where you mount the turn coordinator. Tim Auckland wrote: (Things are so slow in this group at the moment, I thought I'd post this to get your input on something I've been mulling over...) If you put a plane into a skidding left turn (wings level) with left rudder, the ball on the panel goes to the right. However, I've been trying to work out what would happen to the ball if it was mounted on the tail. The rudder is pushing the tail of the plane to the right, so I think the ball would go to the left. Can anyone confirm this? Tim. |
#4
|
|||
|
|||
Mounting a turn coordinator on the tail?
What causes a plane to turn is the horizontal component of the lift
vector. It certainly does not depend on the turn coordinator. What counts is the center of gravity of the plane, not the tail. Tim Auckland wrote: Stubby, Thanks, I think I've got it now. As the turn is initiated, the tail has to go right (this is what causes the plane to turn) and my guess is that the ball initially goes very slightly left. However, once a constant-radius turn has been achieved, the ball will be on the right (outside) of the turn. Tim. On Sat, 29 Jul 2006 18:28:28 -0400, Stubby wrote: I don't think so. My understanding is the ball rests in a slightly curved tube, arranged so that gravity tends to center it. Centrifugal force tries to move it to the outside of the skid, up the curved tube. Neither of these forces depends on where you mount the turn coordinator. Tim Auckland wrote: (Things are so slow in this group at the moment, I thought I'd post this to get your input on something I've been mulling over...) If you put a plane into a skidding left turn (wings level) with left rudder, the ball on the panel goes to the right. However, I've been trying to work out what would happen to the ball if it was mounted on the tail. The rudder is pushing the tail of the plane to the right, so I think the ball would go to the left. Can anyone confirm this? Tim. |
#5
|
|||
|
|||
Mounting a turn coordinator on the tail?
I've never quite bought in to the "horizontal component of lift"
explanation for what causes a plane to turn. I started this discussion talking about a "wings level skidding turn". There's no horizontal component of lift generated by the wings if the wings are level. There is however a couple comprising of the rightwards force from the rudder, and the induced leftwards force of wind resistance acting further forward along the fuselage. It's the couple which causes the plane to turn. I can also generate a substantial amount of horizontal force from the wings without the plane turning (think forward slip); it just moves sideways through the air. I believe what causes a plane to turn is the couple comprised of opposing forces which aren't aligned. For example, in a coordinated left turn, the wings generate a horizontal force to the left. The tail generates a horizontal force to the right. The forces aren't aligned, so a couple is generated, and the airplane turns left. Without a force to the right, the "horizontal component of lift" to the left generated by the banked wings would merely cause the plane to move left -- it wouldn't turn. Just my $0.10 worth, and I'll happily listen to contradictory arguments. Tim. On Sat, 29 Jul 2006 20:52:00 -0400, Stubby wrote: What causes a plane to turn is the horizontal component of the lift vector. It certainly does not depend on the turn coordinator. What counts is the center of gravity of the plane, not the tail. Tim Auckland wrote: Stubby, Thanks, I think I've got it now. As the turn is initiated, the tail has to go right (this is what causes the plane to turn) and my guess is that the ball initially goes very slightly left. However, once a constant-radius turn has been achieved, the ball will be on the right (outside) of the turn. Tim. On Sat, 29 Jul 2006 18:28:28 -0400, Stubby wrote: I don't think so. My understanding is the ball rests in a slightly curved tube, arranged so that gravity tends to center it. Centrifugal force tries to move it to the outside of the skid, up the curved tube. Neither of these forces depends on where you mount the turn coordinator. Tim Auckland wrote: (Things are so slow in this group at the moment, I thought I'd post this to get your input on something I've been mulling over...) If you put a plane into a skidding left turn (wings level) with left rudder, the ball on the panel goes to the right. However, I've been trying to work out what would happen to the ball if it was mounted on the tail. The rudder is pushing the tail of the plane to the right, so I think the ball would go to the left. Can anyone confirm this? Tim. |
#6
|
|||
|
|||
Mounting a turn coordinator on the tail?
I started this discussion talking about a "wings level skidding turn".
There's no horizontal component of lift generated by the wings if the wings are level. There is however a couple comprising of the rightwards force from the rudder, and the induced leftwards force of wind resistance acting further forward along the fuselage. It's the couple which causes the plane to turn. There is also the fact that the thrust vector is more aligned with the direction of desired flight. I believe what causes a plane to turn is the couple comprised of opposing forces which aren't aligned. This is always true, for any acceleration not in the direct line of flight. There is no "one thing" which causes anything in aviation (except at the most fundamental level, where all flight is controlled by money). In a coordinated turn, there are several forces, as you pointed out. However, not all turns are coordinated. What makes a car turn? Are there analogs in aviation of these forces? Jose -- The monkey turns the crank and thinks he's making the music. for Email, make the obvious change in the address. |
#7
|
|||
|
|||
Mounting a turn coordinator on the tail?
Tim Auckland wrote:
(Things are so slow in this group at the moment, I thought I'd post this to get your input on something I've been mulling over...) If you put a plane into a skidding left turn (wings level) with left rudder, the ball on the panel goes to the right. However, I've been trying to work out what would happen to the ball if it was mounted on the tail. The rudder is pushing the tail of the plane to the right, so I think the ball would go to the left. Can anyone confirm this? Tim. If you are coordinated, the ball will be centered If you are slipping, or skidding, the ball will be just the same as if it was in the panel. Dave |
#8
|
|||
|
|||
Mounting a turn coordinator on the tail?
On Sat, 29 Jul 2006 15:52:39 -0600, Tim Auckland wrote:
(Things are so slow in this group at the moment, I thought I'd post this to get your input on something I've been mulling over...) If you put a plane into a skidding left turn (wings level) with left rudder, the ball on the panel goes to the right. However, I've been trying to work out what would happen to the ball if it was mounted on the tail. The rudder is pushing the tail of the plane to the right, so I think the ball would go to the left. Can anyone confirm this? Tim. In the situation you describe, the ball should first go to the left, as the tail is pushed out to the right by the action of the rudder. Once the skid is stable, and the ball will go over to the right, to reflect the fact that the aircraft (including its tail) is turning left. |
#9
|
|||
|
|||
Mounting a turn coordinator on the tail?
Tim Auckland wrote in news:eglnc2tk7l96o5qq3mqajbujfip02iaaol@
4ax.com: (Things are so slow in this group at the moment, I thought I'd post this to get your input on something I've been mulling over...) If you put a plane into a skidding left turn (wings level) with left rudder, the ball on the panel goes to the right. However, I've been trying to work out what would happen to the ball if it was mounted on the tail. The rudder is pushing the tail of the plane to the right, so I think the ball would go to the left. Can anyone confirm this? Tim. More importantly, if you put the TC in the tail, how much rudder pressure would the pilot have to apply in order to turn the tail quickly enough around to see it? I believe cats and dogs have the ability to achieve the necessary speeds, almost even to the point that some may catch their tails in their mouths as they look to focus on their balls. But I don't think airplanes are quite limber enough for this capability. |
#10
|
|||
|
|||
Mounting a turn coordinator on the tail?
Stubby wrote:
What causes a plane to turn is the horizontal component of the lift vector. It certainly does not depend on the turn coordinator. What counts is the center of gravity of the plane, not the tail. BZZT. Incorrect over simplification and psuedoscientific drivel given by the FAA. If you believed the FAA description, then the airplane would just translate sidewise rather than turning in a circle. While the horizontal component of lift is what pulls you to the interior of the turn, the tail is VERY important to actually "turn" the aircraft direction so that the horizontal component continually gets pointed to the center of the turn. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Most reliable homebuilt helicopter? | tom pettit | Home Built | 35 | September 29th 05 02:24 PM |
Tail flapper failure | Veeduber | Home Built | 2 | May 22nd 04 06:52 AM |
Rate of turn indicator on commercial jets (Boeing / Airbus) | Mark | Simulators | 1 | November 1st 03 10:35 AM |
IFR in the 1930's | Dick | Restoration | 26 | September 11th 03 07:42 PM |
Oshkosh Get together Roster - Sign in, please! | Bruce E. Butts | Home Built | 4 | July 26th 03 11:34 AM |