A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Owning
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Aircraft Recovery Dolly



 
 
Thread Tools Display Modes
  #1  
Old April 16th 09, 03:48 PM posted to rec.aviation.owning
John[_9_]
external usenet poster
 
Posts: 103
Default Aircraft Recovery Dolly

I need to acquire a dolly capable of recovering a typical general
aviation aircraft with a flat tire.
I would like something that I can just place the flat tire wheel
assembly onto without removing wheel pants or brakes. It also needs
to be capable of being towed up to a mile using only one tug.

Any ideas?
  #2  
Old April 17th 09, 02:19 AM posted to rec.aviation.owning
BT
external usenet poster
 
Posts: 995
Default Aircraft Recovery Dolly

A sturdy mechanics creeper? not a cheap wood one that would sag.
move slowly

"John" wrote in message
...
I need to acquire a dolly capable of recovering a typical general
aviation aircraft with a flat tire.
I would like something that I can just place the flat tire wheel
assembly onto without removing wheel pants or brakes. It also needs
to be capable of being towed up to a mile using only one tug.

Any ideas?



  #3  
Old April 21st 09, 04:34 PM posted to rec.aviation.owning
John T[_6_]
external usenet poster
 
Posts: 1
Default Aircraft Recovery Dolly


I assume you are planning to use a jack to raise the wheel with the flat?

The creeper concept is ok, but the first problem is the weight. You
need to expect 1000 lb per wheel for a single (Bonanza). Sure, the
passengers will be out, but the plane may be full of fuel and baggage.

The wheels on a creeper or on the dollies sold at Home Depot are another
issue. Even if they could take the weight, they are just too small for
cracked taxiways.

I recently moved a 650 lb grand piano and bought my supplies from Movers
Supply House in the Bronx. They sell a variety of dollies under $150.

There are also piano mover dollies designed for outdoor use, including
some with air tires. I would investigate those, too.

Good luck.

-John


BT wrote:
A sturdy mechanics creeper? not a cheap wood one that would sag.
move slowly

"John" wrote in message
...
I need to acquire a dolly capable of recovering a typical general
aviation aircraft with a flat tire.
I would like something that I can just place the flat tire wheel
assembly onto without removing wheel pants or brakes. It also needs
to be capable of being towed up to a mile using only one tug.

Any ideas?



  #4  
Old April 22nd 09, 11:21 PM posted to rec.aviation.owning
Capt. Geoffrey Thorpe
external usenet poster
 
Posts: 790
Default Aircraft Recovery Dolly

..
"John T" wrote in message
news:1IlHl.1340$io.136@llnews...

I assume you are planning to use a jack to raise the wheel with the flat?

The creeper concept is ok, but the first problem is the weight. You need
to expect 1000 lb per wheel for a single (Bonanza). Sure, the passengers
will be out, but the plane may be full of fuel and baggage.

The wheels on a creeper or on the dollies sold at Home Depot are another
issue. Even if they could take the weight, they are just too small for
cracked taxiways.



http://www.northerntool.com/webapp/w...5530_200365530

Wheels are 3"

--
Geoff
The Sea Hawk at Wow Way d0t Com
remove spaces and make the obvious substitutions to reply by mail
When immigration is outlawed, only outlaws will immigrate

  #5  
Old April 23rd 09, 11:12 PM posted to rec.aviation.owning
Morgans[_2_]
external usenet poster
 
Posts: 3,924
Default Aircraft Recovery Dolly


"Capt. Geoffrey Thorpe" The Sea Hawk @See My Sig.com wrote

Wheels are 3"


I have found you need at least 6" wheels to be used on outdoor pavement,
with heavy loads.

I suggest air filled wheelbarrow wheels, 4 of them mounted on the sides of
two pieces of angle iron, with the bottom of the angles extended wide enough
for the wheel to sit on an inch or so off the ground.
--
Jim in NC


  #6  
Old April 27th 09, 03:20 PM posted to rec.aviation.owning
Jay Masino
external usenet poster
 
Posts: 46
Default Aircraft Recovery Dolly

Here's a design that I've been mulling over. Since I don't have the
ability to weld something up, I was considering a double thickness
of 3/4" pressure treated plywood. If you can get a 2' x 4' piece, then
cut it in half and glue/screw the two together to get a 2' x 2' slab of
plywood that's 1 1/2" thick. Then mount 4 of something like these:
http://www.northerntool.com/webapp/w...029422_1029422

using through-bolts, fender washers and locknuts.

You'd get approx 1200' capacity with not too much cost.

--- Jay



--

Jay Masino "Home is where My critters are"
http://www.JayMasino.com
http://www.OceanCityAirport.com
http://www.oc-Adolfos.com
  #7  
Old August 6th 09, 08:03 PM posted to rec.aviation.owning
Gary Peek
external usenet poster
 
Posts: 1
Default Aircraft Recovery Dolly

John wrote:
I need to acquire a dolly capable of recovering a typical general
aviation aircraft with a flat tire.
I would like something that I can just place the flat tire wheel
assembly onto without removing wheel pants or brakes. It also needs
to be capable of being towed up to a mile using only one tug.

Any ideas?


Have done it with a 4 wheel dolly, but it was one of
the really sturdy ones that moving companies use.

McMaster-Carr has many of them, but I don't know which
model would be it. www.mcmaster.com
  #8  
Old May 16th 14, 03:53 AM posted to rec.aviation.owning
[email protected]
external usenet poster
 
Posts: 1
Default Aircraft Recovery Dolly

On Thursday, April 16, 2009 7:48:26 AM UTC-7, John wrote:
I need to acquire a dolly capable of recovering a typical general
aviation aircraft with a flat tire.
I would like something that I can just place the flat tire wheel
assembly onto without removing wheel pants or brakes. It also needs
to be capable of being towed up to a mile using only one tug.

Any ideas?


go to theirontire.com for the answer
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
LS4 tail dolly Leigh Soaring 0 May 30th 08 02:02 AM
ASK-21 - is a tail dolly necessary? Dave Springford Soaring 7 December 31st 07 09:43 AM
FS: ASW-24 Tail Dolly [email protected] Soaring 0 December 26th 06 03:40 PM
WTB: used tail dolly David Campbell Soaring 5 April 17th 06 03:19 PM
assembly dolly Udo Rumpf Soaring 0 April 29th 05 04:17 PM


All times are GMT +1. The time now is 07:54 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 AviationBanter.
The comments are property of their posters.