Multi-Engine Before Commercial?

"David B. Cole" wrote in message
m...

But does it make sense to do the multi before the Comm, and would I
receive more benefit from following my original plan?


It makes more sense to do the multi then do the commercial in the multi
engine. The guys who say that you can do the cross countries in the single
and then do a multi add-on are only half right. Much of the cross country in
a single must be solo, but you can do it dual in a multi-engine, thus
meeting the requirements for dual training at the same time as the cross
country, cutting the total hours considerably. At your point, I would
recommend the multi-engine private and get the multi-engine instrument at
the same time -- you only have to add a couple of approaches to the check
ride. Then do all the commercial training in a multi-engine plane; it serves
as a complex airplane. Then go back and do the single-engine add-on. All you
have to do then is the single-engine maneuvers, no cross country and no
complex training.

"C J Campbell" wrote:
Then do all the commercial training in a multi-engine plane; it serves
as a complex airplane.

Not all multi's are complex (nor are they all high-performance).
Granted, you need to look hard to find one that isn't, but it's
possible. It would be embarrassing to show up for a checkride and have
the examiner tell you the airplane you brought doesn't qualify.

In article , Roy Smith
wrote:

"C J Campbell" wrote:
Then do all the commercial training in a multi-engine plane; it serves
as a complex airplane.

Not all multi's are complex (nor are they all high-performance).

Aeronca Lancer, for instance.

Sorry to hi-jack this thread for a couple of questions...

I have my FAA Commercial and Instrument with Single Engine privilages, this
was gained last year. At the end of June this year I am undergoing training
for my FAA Multi Addon to my Commercial together with Multi Instrument
Privilages.

From what I understand all I need to do is a multi engine course and pass a
checkride / oral during which I am required to demonstrate single engine IFR
approaches. Is this all that is required? Or do I need to complete the
dual cross countries again, in a multi? Of course all of the Commercial
requirements were met in the Single and as yet I have no multi time.

If it makes any difference, my Commercial was done under Part 61 and took
four days (including checkride) straight after the Part 141 Instrument
course.

Also would you recommend a Part 61 or Part 141 Multi Engine Addon? I'm
taking a couple of weeks off work to get this completed full time.

Best wishes,

Richard Thomas
FAA CP-ASEL IA


"C J Campbell" wrote in message
...

"David B. Cole" wrote in message
m...

But does it make sense to do the multi before the Comm, and would I
receive more benefit from following my original plan?


It makes more sense to do the multi then do the commercial in the multi
engine. The guys who say that you can do the cross countries in the single
and then do a multi add-on are only half right. Much of the cross country
in
a single must be solo, but you can do it dual in a multi-engine, thus
meeting the requirements for dual training at the same time as the cross
country, cutting the total hours considerably. At your point, I would
recommend the multi-engine private and get the multi-engine instrument at
the same time -- you only have to add a couple of approaches to the check
ride. Then do all the commercial training in a multi-engine plane; it
serves
as a complex airplane. Then go back and do the single-engine add-on. All
you
have to do then is the single-engine maneuvers, no cross country and no
complex training.

"Richard Thomas" wrote in message Also would you recommend a Part 61 or
Part 141 Multi Engine Addon? I'm
taking a couple of weeks off work to get this completed full time.

A multi add-on can be done in a couple of days. Part 61 vs 141 won't make
much difference.

D.

You do not need to re accomplish the cross countries.. you do need to be
prepared to complete the "multi" part of the PTS, engine cuts on takeoff,
Sim Engine Failure at altitude, etc. I had even practiced some Lazy8s and
Chandelles, but they were not requested on the check ride. It was the same
DE that had completed my SEL COMM a month prior.

My ME add-on with Instrument privileges went like this.
Oral, standard systems and difference questions, MinControlAirspeed etc.

Then the flight, preflight, initial take off with an engine cut as soon as
power was established, I cut the other engine and started to brake, Examiner
restored the engine (said it was mine) and brought the power back up for
take off, some engine cuts on take off will result in a full taxi back for a
second takeoff. We had pre-briefed this procedure and had a very long
runway.

On climbout and safe altitude, the DE again reduced power on one engine
(hiding the throttles) and I did the "dead foot dead engine" routine and
identified which I would shut down by placing my hand on the proper mixture
control and verbalized the checklist to shut it down. The "dead engine" was
then restored to full power.

On the hood, picked up radar vectors to a FULL ILS approach, missed approach
back to the radar pattern for a LOC approach with one engine simulated shut
down, (reduced to zero thrust by the DE). Engine restored for the go around,
but not really needed, it was a SenecaII Turbo.

Both good engines, under the hood to the practice area, headings and
altitudes provided by the DE. Some other IFR work, attitude recovery, etc,
then demo a full engine shut down are restart while maintaining heading and
altitude. As the engine warmed back up, the hood came off and MCA
demonstrations were completed.

Then a sim engine out VFR approach to the home airport to a touch and two
engine go, a VFR pattern with both engines for the accuracy landing. Full
Stop, mission complete.

Remember while all this is going on, the PIC (person taking the checkride)
is handling all radios and checklist as if SOLO.

BT

"Richard Thomas" wrote in message
...
Sorry to hi-jack this thread for a couple of questions...

I have my FAA Commercial and Instrument with Single Engine privilages,
this
was gained last year. At the end of June this year I am undergoing
training
for my FAA Multi Addon to my Commercial together with Multi Instrument
Privilages.

From what I understand all I need to do is a multi engine course and pass
a
checkride / oral during which I am required to demonstrate single engine
IFR
approaches. Is this all that is required? Or do I need to complete the
dual cross countries again, in a multi? Of course all of the Commercial
requirements were met in the Single and as yet I have no multi time.

If it makes any difference, my Commercial was done under Part 61 and took
four days (including checkride) straight after the Part 141 Instrument
course.

Also would you recommend a Part 61 or Part 141 Multi Engine Addon? I'm
taking a couple of weeks off work to get this completed full time.

Best wishes,

Richard Thomas
FAA CP-ASEL IA


"C J Campbell" wrote in message
...

"David B. Cole" wrote in message
m...

But does it make sense to do the multi before the Comm, and would I
receive more benefit from following my original plan?


It makes more sense to do the multi then do the commercial in the multi
engine. The guys who say that you can do the cross countries in the
single
and then do a multi add-on are only half right. Much of the cross
country
in
a single must be solo, but you can do it dual in a multi-engine, thus
meeting the requirements for dual training at the same time as the cross
country, cutting the total hours considerably. At your point, I would
recommend the multi-engine private and get the multi-engine instrument
at
the same time -- you only have to add a couple of approaches to the
check
ride. Then do all the commercial training in a multi-engine plane; it
serves
as a complex airplane. Then go back and do the single-engine add-on. All
you
have to do then is the single-engine maneuvers, no cross country and no
complex training.

"C J Campbell" wrote in message ...

It makes more sense to do the multi then do the commercial in the multi
engine. The guys who say that you can do the cross countries in the single
and then do a multi add-on are only half right. Much of the cross country in
a single must be solo, but you can do it dual in a multi-engine, thus
meeting the requirements for dual training at the same time as the cross
country, cutting the total hours considerably. At your point, I would
recommend the multi-engine private and get the multi-engine instrument at
the same time -- you only have to add a couple of approaches to the check
ride. Then do all the commercial training in a multi-engine plane; it serves
as a complex airplane. Then go back and do the single-engine add-on. All you
have to do then is the single-engine maneuvers, no cross country and no
complex training.

How are you going to get the 10 hours of multi solo time required for
an initial commerical in a multi? Are there any FBOs that rent multi's
to non-rated pilots? You'll either need to do a private add on
checkride just to get the solo time or get signed off solo in the
multi but not find insurance. It seems easier to just get your private
commerical and then spend 10-15 hours in the twin for the add-on
checkride ( you don't need a private multi to take take the commerial
multi add-on checkride).

-Robert

"Robert M. Gary" wrote in message
om...
"C J Campbell" wrote in message
...

It makes more sense to do the multi then do the commercial in the multi
engine. The guys who say that you can do the cross countries in the
single
and then do a multi add-on are only half right. Much of the cross
country in
a single must be solo, but you can do it dual in a multi-engine, thus
meeting the requirements for dual training at the same time as the cross
country, cutting the total hours considerably. At your point, I would
recommend the multi-engine private and get the multi-engine instrument
at
the same time -- you only have to add a couple of approaches to the
check
ride. Then do all the commercial training in a multi-engine plane; it
serves
as a complex airplane. Then go back and do the single-engine add-on. All
you
have to do then is the single-engine maneuvers, no cross country and no
complex training.

How are you going to get the 10 hours of multi solo time required for
an initial commerical in a multi?

There is no such requirement. Perhaps you are thinking of 61.129 (b) which
says:

(4) 10 hours of solo flight time in a multiengine airplane or 10 hours of
flight time performing the duties of pilot in command in a multiengine
airplane with an authorized instructor (either of which may be credited
towards the flight time requirement in paragraph (b)(2) of this section), on
the areas of operation listed in §61.127(b)(2) of this part that includes at
least-

(Robert M. Gary) wrote in message
How are you going to get the 10 hours of multi solo time required for
an initial commerical in a multi?

read the regulations again, there is no such requirements on the book.

--Sylvain