![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
![]()
("john smith" wrote)
Do you use grass airstrips? Are you going to AirVenture? Cut three 1-foot x 1-foot squares of marine plywood (not particle board) of one-inch thickness. Stop just short of where you park the airplane. Climb out, pull out the boards, place them ahead of each wheel. With help, pull the airplanes wheels onto the plywood. When you are ready to leave, pull the airplane off the plywood and stow them away for the next use. This prevents yours wheels form sinking into the ground and requiring high engine power to pull the airplane free from the ruts. Montblanc may be selling them at the R.A.P gathering this summer at AirVenture. 1-ft x 1-ft square was found to be somewhat ...ungood. I would recommend at least 1-ft x 18 inches. I'll have to start saving scraps of plywood. For long term use, marine plyw$$d is great! For one week at OSH ...we'll see what I find. Cost? Free. Montblack |
#2
|
|||
|
|||
![]()
I'll have to start saving scraps of plywood. For long term use, marine
plyw$$d is great! For one week at OSH ...we'll see what I find. Cost? Free. Montblack Dibs on the first pair! Um...along with assorted camping gear. No lumpy pillows please? Does the plywood come with N-numbers stenciled on? In matching colors? Remember, no lumpy pillows. :-) -- Jack Allison PP-ASEL-Instrument Airplane Arrow N2104T "When once you have tasted flight, you will forever walk the Earth with your eyes turned skyward, for there you have been, and there you will always long to return" - Leonardo Da Vinci (Remove the obvious from address to reply via e-mail) |
#3
|
|||
|
|||
![]()
I'll have to start saving scraps of plywood. For long term use, marine
plyw$$d is great! For one week at OSH ...we'll see what I find. Dibs on the first pair! Um...along with assorted camping gear. No lumpy pillows please? Does the plywood come with N-numbers stenciled on? In matching colors? Remember, no lumpy pillows. :-) Us too, us too! Well, skip the pillows -- those we've got. But plywood is something you could sell in the North 40 for a tidy little profit... EVERYONE forgets to bring it. -- Jay Honeck Iowa City, IA Pathfinder N56993 www.AlexisParkInn.com "Your Aviation Destination" |
#4
|
|||
|
|||
![]()
("Jack Allison" wrote)
Dibs on the first pair! Um...along with assorted camping gear. No lumpy pillows please? Does the plywood come with N-numbers stenciled on? In matching colors? Remember, no lumpy pillows. :-) First set (Beta!!) goes to Jack. By 2.0 we'll have figured out it's a good thing to pound down the nails in the old pallets. By 3.0 we'll have figured out not to use old pallets. :-) I'm heading down to the theater shop on Monday. I've called dibbs on all of the 18" stock. 2x4, 2x6, 2x8, plywood, etc. All the leftover pieces. Montblack Camping gear is a go. |
#5
|
|||
|
|||
![]()
Hey guys, take a piece of cardboard big enough to cover the bottom of your
baggage compartment and make a stencil of the floor. Then design your plywood pieces to cover the floor of the baggage compartment completely and snuggly. If you want to get fancy, rabbit joint the edges so they lay on top of each other. It'll make a great support platform for the baggage and spread the load out over the entire floor area. When we pulled the floor out of the rear baggage compartment of our Aztec, we found two support stringers that were broken at the ends (where they rivet to the side stringers). That piece of plywood is now a permanent member of our W&B, in fact, I even upholstered it and it blends right in. Jim "Montblack" wrote in message ... ("john smith" wrote) Do you use grass airstrips? Are you going to AirVenture? Cut three 1-foot x 1-foot squares of marine plywood (not particle board) of one-inch thickness. Stop just short of where you park the airplane. Climb out, pull out the boards, place them ahead of each wheel. With help, pull the airplanes wheels onto the plywood. When you are ready to leave, pull the airplane off the plywood and stow them away for the next use. This prevents yours wheels form sinking into the ground and requiring high engine power to pull the airplane free from the ruts. Montblanc may be selling them at the R.A.P gathering this summer at AirVenture. 1-ft x 1-ft square was found to be somewhat ...ungood. I would recommend at least 1-ft x 18 inches. I'll have to start saving scraps of plywood. For long term use, marine plyw$$d is great! For one week at OSH ...we'll see what I find. Cost? Free. Montblack |
#6
|
|||
|
|||
![]()
("Jim Burns" wrote)
[snip] Hey guys, take a piece of cardboard big enough to cover the bottom of your baggage compartment and make a stencil of the floor. Then design your plywood pieces to cover the floor of the baggage compartment completely and snuggly. I've got a 4x8 sheet of 3/4 plywood back there now. :-) Montblack OMG ...at (1-ft x 1-ft) that's 32 squares. Hey guys, it's not funny anymore. Put down those saws and back away from the minivan before someone gets hurt. |
#7
|
|||
|
|||
![]()
In article ,
"Montblack" wrote: OMG ...at (1-ft x 1-ft) that's 32 squares. Hey guys, it's not funny anymore. And you need 33 pieces for 11 tricycle gear airplanes. Now what are you going to do??? |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Have you created anything "home-made" for your plane? (or a low cost alternative?) | Andy | Piloting | 69 | April 29th 06 03:25 PM |
Washington DC airspace closing for good? | tony roberts | Piloting | 153 | August 11th 05 12:56 AM |
Boeing Boondoggle | Larry Dighera | Military Aviation | 77 | September 15th 04 02:39 AM |
Naval Air Refueling Needs Deferred in Air Force Tanker Plan | Henry J Cobb | Military Aviation | 47 | May 22nd 04 03:36 AM |
Conspiracy Theorists (amusing) | Grantland | Military Aviation | 1 | October 2nd 03 12:17 AM |