A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Home Built
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

measuring flap angles for rigging



 
 
Thread Tools Display Modes
  #1  
Old April 24th 06, 06:07 AM posted to rec.aviation.homebuilt
external usenet poster
 
Posts: n/a
Default measuring flap angles for rigging

What tool or methods do you use to measure flap angles to a datum?

  #3  
Old April 25th 06, 11:51 AM posted to rec.aviation.homebuilt
external usenet poster
 
Posts: n/a
Default measuring flap angles for rigging

A "Smart level" is a tool of choice. It gives you digital read out and is
accurate to 1/10th of a degree.

J.P.
"Stealth Pilot" wrote in message
...
On 23 Apr 2006 22:07:40 -0700, wrote:

What tool or methods do you use to measure flap angles to a datum?


go down to the best hardware store you can find and locate a
carpenter's compound square set. it is the one with the square, the
ruler and the angle doohicky all in one.(two bits that slide along the
ruler) the angle thing has a bubble in it for reference to horizontal.
you discard all the bits except for that bubble angle measurer. it is
more than sufficiently accurate for doing control surfaces.

Stealth Pilot



  #4  
Old April 25th 06, 11:46 PM posted to rec.aviation.homebuilt
external usenet poster
 
Posts: n/a
Default measuring flap angles for rigging

In article , Jean-Paul Roy says...

A "Smart level" is a tool of choice. It gives you digital read out and is
accurate to 1/10th of a degree.


I keep hearing about a "smart level" where does one purchase it?

Thanks

Chuck S


--
NewsGuy.Com 30Gb $9.95 Carry Forward and On Demand Bandwidth

  #5  
Old April 26th 06, 01:38 AM posted to rec.aviation.homebuilt
external usenet poster
 
Posts: n/a
Default measuring flap angles for rigging


"ChuckSlusrczyk" wrote in message
...
In article , Jean-Paul Roy
says...

A "Smart level" is a tool of choice. It gives you digital read out and is
accurate to 1/10th of a degree.


I keep hearing about a "smart level" where does one purchase it?

************************************************** ***
I have one, and it is invaluable.

Building supply stores, magazines or internet outlets.
http://md-smart-tool.com/
--
Jim in NC


  #6  
Old April 26th 06, 01:09 PM posted to rec.aviation.homebuilt
external usenet poster
 
Posts: n/a
Default measuring flap angles for rigging

In article , Morgans says...


"ChuckSlusrczyk" wrote in message
...
In article , Jean-Paul Roy
says...

A "Smart level" is a tool of choice. It gives you digital read out and is
accurate to 1/10th of a degree.


I keep hearing about a "smart level" where does one purchase it?

************************************************* ****
I have one, and it is invaluable.

Building supply stores, magazines or internet outlets.
http://md-smart-tool.com/


Thanks Jim I ordered it this AM.

See ya

Chuck S


--
NewsGuy.Com 30Gb $9.95 Carry Forward and On Demand Bandwidth

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
terminology questions: turtledeck? cantilever wing? Ric Home Built 2 September 13th 05 09:39 PM
Negative flaps for better low speed aileron control? [email protected] Soaring 41 August 25th 05 06:01 AM
Stuck cowl flap cable Jim Burns Owning 7 March 24th 05 02:07 PM
Flap Hinge Moment Calc Bo Home Built 2 February 2nd 05 10:26 AM
Flap angles DeltaDeltaDelta Piloting 34 May 18th 04 12:09 AM


All times are GMT +1. The time now is 03:33 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 AviationBanter.
The comments are property of their posters.