A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Home Built
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Good news for scratch builders of metal airplanes - Home Depot rents bending brakes



 
 
Thread Tools Display Modes
  #1  
Old January 5th 07, 10:19 PM posted to rec.aviation.homebuilt
Capt. Geoffrey Thorpe
external usenet poster
 
Posts: 790
Default Good news for scratch builders of metal airplanes - Home Depot rents bending brakes

"flybynightkarmarepair" wrote in message
ups.com...
If you're building in aluminum from scratch, one of the most
intractable problems is the need for an 8 ft bending brake for most
designs. A good one, even used, is about $1000, and at least half that
many pounds, although there are alternatives that weigh less.
http://www.guttersupply.com/products...ategoryId=1277
There are various ways to do a pretty good job with cheaper tooling,
but I think Dave Thatcher, the designer of the neat CX-4 VW powered
single seater

... This is a GREAT find. It makes me wonder if other tool rental places
have bending brakes.


If they rent construction related equipment, most likely they will have a
siding brake. I've rented them on more than one occasion (to hang
siding/trim).

... The foot is not adjustable, so you will need to bend two 8 ft long
strips of .020 about 2" wide to add to the foot. This will give you a
nice radius on your bends.


This is an important bit of information - the standard radius on a siding
brake is real small.

--
Geoff
The Sea Hawk at Wow Way d0t Com
remove spaces and make the obvious substitutions to reply by mail
When immigration is outlawed, only outlaws will immigrate.


  #2  
Old January 6th 07, 12:03 AM posted to rec.aviation.homebuilt
flybynightkarmarepair
external usenet poster
 
Posts: 106
Default Good news for scratch builders of metal airplanes - Home Depot rents bending brakes


Capt. Geoffrey Thorpe wrote:
"flybynightkarmarepair" wrote in message
ups.com...
If you're building in aluminum from scratch, one of the most
intractable problems is the need for an 8 ft bending brake for most
designs. A good one, even used, is about $1000, and at least half that
many pounds, although there are alternatives that weigh less.
http://www.guttersupply.com/products...ategoryId=1277
There are various ways to do a pretty good job with cheaper tooling,
but I think Dave Thatcher, the designer of the neat CX-4 VW powered
single seater

... This is a GREAT find. It makes me wonder if other tool rental places
have bending brakes.


If they rent construction related equipment, most likely they will have a
siding brake. I've rented them on more than one occasion (to hang
siding/trim).


Well, it turns out this is a REGIONAL phenomena. Here in Northern
California, houses are sheathed with Stucco, shingles, or wood siding.
You almost never see aluminum siding in this neck of the woods. Thus,
there seems to be no call in the rental market around here for the sort
of portable gutter or siding brake that seems to be common in Florida
;-(

I called every Home Depot Rental center within 50 miles, nothing. I
called every OTHER rental center within a smaller radius, nothing. The
counter guy (who is also the owner) of my favorite local rental outfit
said: "I've been in a lot of rental yards over the years, and I've
never seen one; we get questions about once a year, and that's not
enough demand to invest in that tool".

So I'm back at square one, me. Your Mileage May Vary.

  #3  
Old January 6th 07, 12:40 AM posted to rec.aviation.homebuilt
Capt. Geoffrey Thorpe
external usenet poster
 
Posts: 790
Default Good news for scratch builders of metal airplanes - Home Depot rents bending brakes

"flybynightkarmarepair" wrote in message
ups.com...

Capt. Geoffrey Thorpe wrote:

...
If they rent construction related equipment, most likely they will have a
siding brake. I've rented them on more than one occasion (to hang
siding/trim).


Well, it turns out this is a REGIONAL phenomena. Here in Northern
California, houses are sheathed with Stucco, shingles, or wood siding.
You almost never see aluminum siding in this neck of the woods. Thus,
there seems to be no call in the rental market around here for the sort
of portable gutter or siding brake that seems to be common in Florida
;-(

I called every Home Depot Rental center within 50 miles, nothing. I
called every OTHER rental center within a smaller radius, nothing. The
counter guy (who is also the owner) of my favorite local rental outfit
said: "I've been in a lot of rental yards over the years, and I've
never seen one; we get questions about once a year, and that's not
enough demand to invest in that tool".


I guess you learn something every day.
I can think of 4 places to rent one within 5 miles of my house (near
Detroit). Plus two places that just sell siding / trim. Don't see much
Stucco though. :-)

(Most siding is vinyl now - but a lot of trim is still bent on the job)

--
Geoff
The Sea Hawk at Wow Way d0t Com
remove spaces and make the obvious substitutions to reply by mail
When immigration is outlawed, only outlaws will immigrate.


  #4  
Old January 6th 07, 04:22 PM posted to rec.aviation.homebuilt
Lou
external usenet poster
 
Posts: 403
Default Good news for scratch builders of metal airplanes - Home Depot rents bending brakes

Now that you mention it, I've never seen aluminum siding go on a
califonia
house during one of those house flipping shows. I sit there thinking
that these
people sure do pay alot for siding, but your right, no aluminum or
vinyl.
Lou

 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
24 Mar 2006 - Today’s Military, Veteran, War and National Security News Otis Willie Naval Aviation 0 March 25th 06 02:23 AM
20 Nov 2005 - Today's Military, Veteran, War and National Security News Otis Willie Naval Aviation 0 November 20th 05 09:43 PM
American nazi pond scum, version two bushite kills bushite Naval Aviation 0 December 21st 04 10:46 PM
Hey! What fun!! Let's let them kill ourselves!!! [email protected] Naval Aviation 2 December 17th 04 09:45 PM


All times are GMT +1. The time now is 08:19 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 AviationBanter.
The comments are property of their posters.