![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
![]() "Dan G" wrote in message ... On Nov 29, 5:38 pm, "Bill Daniels" bildan@comcast-dot-net wrote: Yes, they certainly pull against the heavy payout brake - they have to, they're using steel cable. You have to keep steel under tension to prevent tangles. Spectra/Dyneema doesn't need that tension. The pay-out brake is not to keep the line under tension, it's to stop the drum when the retrieve stops, or the drum keeps turning and paying out cable which forms great big loops hanging down from the drum. A drum of UHMWPE will of course be much lighter than a steel one, but the drum itself is heavy enough. If the brake is weak you have to tow very slowly, which is frustrating. I bet it's frustrating. Why don't you re-engineer it so it works right. You need to re-think tension. Steel needs to be kept under tension any time you are moving it. If it is just laying in the grass, it's still under a little tension due to friction with the grass. If it takes 70hp to pull out the cable, you're using way too much brake. Tension control winches use the hydraulic motor to provide light reverse torque, not a brake. It takes very little reverse torque to prevent over runs with UHMWPE. Derek says Dyneema doesn't work because it's too expensive, wears out faster than steel and doesn't provide any aditional height. Evedence from many other sites successfuly using Dyneema is to the contrary on all points. The difference is that successful sites did their homework and made all the neccessary changes. Lasham isn't the only club that tried UHMWPE and abadonded it. Pocklington tried it too - with a brand new Skylaunch winch - and also abandoned it. Another club I know well is only using up their current stock of it before reverting to steel. A number of sites had initially very favourable results with UHMWPE but I've never seen any follow-up results, which were promised by the BGA but have never materialised (afaik). The start of this thread was about some very talented folkes in Belgium who set a release height record using UHMWPE on a winch designed for it. UHMWPE is a spectacular success as a winch rope. It beats steel on all counts including wear and life. In fact it lasts long enough to actually be cheaper than steel on a per launch basis. BUT, you have to understand it AND you winch has to be designed for it. Skylaunch is a great steel cable winch. However, it would need a lot of modifications to make it a successful UHMWPE winch. I sincerely hope they do this since it would be easier than trying to convince the world that UHMWPE doesn't work. UHMWPE has never failed anyone but some people trying to use it have failed to use it properly. If you want to know how to use it right, talk to the people who succeeded not the ones who failed. Make a call to Belgium. Bill Daniels |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
How to get maximum height on a winch launch? | Dan G | Soaring | 38 | December 22nd 16 12:29 AM |
Winch launch speed versus height gain | Neil | Soaring | 20 | November 9th 07 12:57 AM |
Record Highs/Record Lows | Jay Honeck | Piloting | 12 | October 12th 06 01:27 AM |
Perlan height record in Argentina | Charles Yeates | Soaring | 3 | September 1st 06 12:59 PM |
LIppmann reports a 950 meter winch launch with their Dynatec winch line - anything higher? | Bill Daniels | Soaring | 20 | December 27th 04 12:33 AM |