![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
![]()
On Mar 21, 10:12*am, Ryan Spicer wrote:
Hi all, * I'm trying to help a club member upload updated waypoint (.dat) files onto his Compaq Aero 1520 for use with GlideNavigator II v3.0. I'm an IT guy, but pretty new to the world of soaring software. We've downloaded the .dat file (http://soaringweb.org/TP/ASA/nm_asa10.dat). It opens correctly in SeeYou, and when we copy it to PocketPC/Storage Card/My Documents, it appears in the list of WP files from within GNII, but when we select "add," to add it to the list of active waypoint files, and remove the old .dat, no waypoints are available within GNII. *Does anyone have any idea what might be causing the problem? What other information should I be looking at to diagnose this? I have the ASA 2010 tp file loaded on my Aero 1530 and it runs just fine with with 2.3 beta 18 which, to the best of my recollection, is the same as 3 except for a different password scheme. There are 3 versions on TP Exchange, name only, number before name, and number after name. The file should be loaded in the CF directory - storage card/SUAsandWPs/ or it can be loaded in the Aero 15xx memory at mydocuments/sSUAsandWPs/ If the CF is present and the directory SUAsandWPs is there GN gets the files from there, not from the local directory. I'm currently using asa_2010.dat because that is my preferred format. I have not tested nm_asa_10.dat with GN but have no reason to think there is anything wrong with file. Try putting the file in the correct directory and see if it works. If not I'll be at the field on Friday if you haven't solved it by then. I'll be at the front end of the rope. Andy (GY) |
#2
|
|||
|
|||
![]()
On Mar 21, 8:44*pm, Andy wrote:
On Mar 21, 10:12*am, Ryan Spicer wrote: Hi all, * I'm trying to help a club member upload updated waypoint (.dat) files onto his Compaq Aero 1520 for use with GlideNavigator II v3.0. I'm an IT guy, but pretty new to the world of soaring software. We've downloaded the .dat file (http://soaringweb.org/TP/ASA/nm_asa10.dat). It opens correctly in SeeYou, and when we copy it to PocketPC/Storage Card/My Documents, it appears in the list of WP files from within GNII, but when we select "add," to add it to the list of active waypoint files, and remove the old .dat, no waypoints are available within GNII. *Does anyone have any idea what might be causing the problem? What other information should I be looking at to diagnose this? I have the ASA 2010 *tp file loaded on my Aero 1530 and it runs just fine with with 2.3 beta 18 which, to the best of my recollection, *is the same as 3 except for a different password scheme. There are 3 versions on TP Exchange, name only, number before name, and number after name. *The file should be loaded in the CF directory - storage card/SUAsandWPs/ *or it can be loaded in the Aero 15xx memory at mydocuments/sSUAsandWPs/ If the CF is present and the directory SUAsandWPs is there GN gets the files from there, not from the local directory. I'm currently using asa_2010.dat because that is my preferred format. I have not tested nm_asa_10.dat with GN but have no reason to think there is anything wrong with file. Try putting the file in the correct directory and see if it works. *If not I'll be at the field on Friday if you haven't solved it by then. I'll be at the front end of the rope. Andy (GY) Ryan, I downloaded the tp file using the link you published in the original post, copied the file to my cf card in the SUAsand Wps subdirectory, opened GNII, deleted the waypoint file I normally use, and added the nm_asa10 file. GN loaded the new file and displayed the waypoints correctly. Note that when GN loads a new file it may assume a current position that is at the "center" of the loaded waypoints. Depending on your map scale you may not see any waypoints displayed. On restart, GN will assume a position equal to the "home" airport coordinates if there is one. For this file "home" is "El Tiro". I also tried adding before delete, adding and not deleting, and it all works as intended. If you can't make it work, and can't wait til Friday, give me a call in the evening. I'm in the TuSC directory. I'll just change you a beer ![]() Andy (GY) |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
How to import turnpoints into SeeYou | Scott Alexander[_2_] | Soaring | 5 | January 12th 10 12:03 PM |
convert turnpoints to KML for google earth? | chris | Soaring | 4 | January 15th 08 10:56 PM |
Region 6 contest turnpoints? | kirk.stant | Soaring | 0 | June 7th 07 07:14 PM |
2006 Region 9 turnpoints | [email protected] | Soaring | 0 | March 15th 06 04:02 AM |
Recording and Deleting Tasks and Turnpoints in the Volkslogger | Nyal Williams | Soaring | 3 | May 18th 05 09:42 PM |