PowerFlarm with FlarmView, I have a question.

On Thursday, May 5, 2016 at 11:17:11 AM UTC-7, wrote:
Here at Chicago Glider Club we have the dubious distinction of flying right under the approach path into Midway airport. I have looked at SouthWest planes coming through from all angles, including head-on. Flying with a C-mode transponder helps a lot, Approach will guide the big iron around us although I'm sometimes wondering about the spacing.
My PFlarm will indicate through the FlarmView display a blue dot around my position that is blinking ONLY when a SW or bigger commercial plane (equipped with TCAS?) is coming through. Could there be a connection such that the transponder when interrogated by a TCAS responds in a way that is picked up by PFlarm? What else might the blue blinking dot mean?
Please enlighten me.
Herb, J7

that is a mode C or mode S transponder it is non directional and as it gets closer the circle should get smaller. Blue means it is above you.

Richard
www.craggyaero.com

It means you should zoom in to be able to tell how far the target is more or less.

Ramy

On Thu, 05 May 2016 11:50:39 -0700, Richard wrote:

On Thursday, May 5, 2016 at 11:17:11 AM UTC-7, wrote:
Here at Chicago Glider Club we have the dubious distinction of flying
right under the approach path into Midway airport. I have looked at
SouthWest planes coming through from all angles, including head-on.
Flying with a C-mode transponder helps a lot, Approach will guide the
big iron around us although I'm sometimes wondering about the spacing.
My PFlarm will indicate through the FlarmView display a blue dot around
my position that is blinking ONLY when a SW or bigger commercial plane
(equipped with TCAS?) is coming through. Could there be a connection
such that the transponder when interrogated by a TCAS responds in a way
that is picked up by PFlarm? What else might the blue blinking dot
mean?
Please enlighten me.
Herb, J7

that is a mode C or mode S transponder it is non directional and as it
gets closer the circle should get smaller. Blue means it is above you.

Richard www.craggyaero.com

I've been bench testing 6.06 firmware, and see what I believe Herb is
seeing. A small flashing dot right at current position, but it's short
lived and never gets bigger. It's like the range for mode c/mode s
targets is terrible. I see lots of ADS-B targets at distances greater
than 12 miles, but hardly any mode c/mode s. Maybe they gave up trying
to estimate distance for those targets?

I fly near a busy airport (KPRC) with several flight schools and lots of targets for my PF with butterfly rectangle display. I get alot of both Adsb and mode c/s targets the mode c consistently show up as rings and seem to jump from 6 miles to 3 miles then 2 and then 1 with a small altitude display above or below to nearest 100' seems pretty straight forward and I don't see any reason to change displays. I also like the dedicated and front and center of where I located the butterfly right on the front lip of my glare shield. Only disadvantage for me is the volume of the alerts could be louder, but I am getting hard of hearing now too

And what are your PowerFLARM's PCAS range and altitude settings set to?

On Saturday, May 7, 2016 at 7:11:29 AM UTC-7, David Kinsell wrote:
On Thu, 05 May 2016 11:50:39 -0700, Richard wrote:

On Thursday, May 5, 2016 at 11:17:11 AM UTC-7, wrote:
Here at Chicago Glider Club we have the dubious distinction of flying
right under the approach path into Midway airport. I have looked at
SouthWest planes coming through from all angles, including head-on.
Flying with a C-mode transponder helps a lot, Approach will guide the
big iron around us although I'm sometimes wondering about the spacing.
My PFlarm will indicate through the FlarmView display a blue dot around
my position that is blinking ONLY when a SW or bigger commercial plane
(equipped with TCAS?) is coming through. Could there be a connection
such that the transponder when interrogated by a TCAS responds in a way
that is picked up by PFlarm? What else might the blue blinking dot
mean?
Please enlighten me.
Herb, J7

that is a mode C or mode S transponder it is non directional and as it
gets closer the circle should get smaller. Blue means it is above you.

Richard www.craggyaero.com

I've been bench testing 6.06 firmware, and see what I believe Herb is
seeing. A small flashing dot right at current position, but it's short
lived and never gets bigger. It's like the range for mode c/mode s
targets is terrible. I see lots of ADS-B targets at distances greater
than 12 miles, but hardly any mode c/mode s. Maybe they gave up trying
to estimate distance for those targets?

Currently using the default flarmcfg.txt file, so 7000 and 600.


Sat, 07 May 2016 10:13:05 -0700, Darryl Ramm wrote:

And what are your PowerFLARM's PCAS range and altitude settings set to?

On Saturday, May 7, 2016 at 7:11:29 AM UTC-7, David Kinsell wrote:
On Thu, 05 May 2016 11:50:39 -0700, Richard wrote:

On Thursday, May 5, 2016 at 11:17:11 AM UTC-7,
wrote:
Here at Chicago Glider Club we have the dubious distinction of
flying right under the approach path into Midway airport. I have
looked at SouthWest planes coming through from all angles, including
head-on. Flying with a C-mode transponder helps a lot, Approach will
guide the big iron around us although I'm sometimes wondering about
the spacing. My PFlarm will indicate through the FlarmView display a
blue dot around my position that is blinking ONLY when a SW or
bigger commercial plane (equipped with TCAS?) is coming through.
Could there be a connection such that the transponder when
interrogated by a TCAS responds in a way that is picked up by
PFlarm? What else might the blue blinking dot mean?
Please enlighten me.
Herb, J7

that is a mode C or mode S transponder it is non directional and as
it gets closer the circle should get smaller. Blue means it is above
you.

Richard www.craggyaero.com

I've been bench testing 6.06 firmware, and see what I believe Herb is
seeing. A small flashing dot right at current position, but it's short
lived and never gets bigger. It's like the range for mode c/mode s
targets is terrible. I see lots of ADS-B targets at distances greater
than 12 miles, but hardly any mode c/mode s. Maybe they gave up trying
to estimate distance for those targets?

So do you have much traffic below ~2,000' AGL where you are? That are also in SSR interrogator coverage? (although TCAS should fill in as an interrogator). Why not try setting everything unlimited and see what happens.

Partial obstructions, local reflections etc. can severely screw with PCAS's estimation of range. Testing that on the ground may be a waste of time.

On Saturday, May 7, 2016 at 11:44:51 AM UTC-7, David Kinsell wrote:
Currently using the default flarmcfg.txt file, so 7000 and 600.


Sat, 07 May 2016 10:13:05 -0700, Darryl Ramm wrote:

And what are your PowerFLARM's PCAS range and altitude settings set to?

On Saturday, May 7, 2016 at 7:11:29 AM UTC-7, David Kinsell wrote:
On Thu, 05 May 2016 11:50:39 -0700, Richard wrote:

On Thursday, May 5, 2016 at 11:17:11 AM UTC-7,
wrote:
Here at Chicago Glider Club we have the dubious distinction of
flying right under the approach path into Midway airport. I have
looked at SouthWest planes coming through from all angles, including
head-on. Flying with a C-mode transponder helps a lot, Approach will
guide the big iron around us although I'm sometimes wondering about
the spacing. My PFlarm will indicate through the FlarmView display a
blue dot around my position that is blinking ONLY when a SW or
bigger commercial plane (equipped with TCAS?) is coming through.
Could there be a connection such that the transponder when
interrogated by a TCAS responds in a way that is picked up by
PFlarm? What else might the blue blinking dot mean?
Please enlighten me.
Herb, J7

that is a mode C or mode S transponder it is non directional and as
it gets closer the circle should get smaller. Blue means it is above
you.

Richard www.craggyaero.com

I've been bench testing 6.06 firmware, and see what I believe Herb is
seeing. A small flashing dot right at current position, but it's short
lived and never gets bigger. It's like the range for mode c/mode s
targets is terrible. I see lots of ADS-B targets at distances greater
than 12 miles, but hardly any mode c/mode s. Maybe they gave up trying
to estimate distance for those targets?

There's some low level traffic around, from local airports. It's
frequently interrogated, I have a separate ADS-B receiver that also shows
mode s targets, and it shows a lot of stuff buzzing around during the
day. Increasing the altitude limits of course adds more. PCAS target
range can only be increased to 10K meters, so that's a limiting factor in
how much you'll ever see with PF.

Doing more experiments, looks like the defaults aren't good at all for
the FlarmViews that Herb and I are using. In particular the protocol for
the RJ45 and d-sub gets set to 'default', much better results with
version 7. From their description, they ought to default to ver 4.
ADS-B vertical range is set for unlimited, a bizarre choice if you're
actually flying. "Process Mode C Targets" is shut off by default.

Not sure how Herb has his configured, but after setting the protocol to
7, I saw an ADS-B target show up with a plane symbol and a flashing ring,
and got the flashing blue dot when the target was right overhead. So it
seems to be a collision alert. A PCAS target showed up as just a
flashing ring, so it's working as expected now. Max range was about 6
miles in both cases.

These results were with latest firmware on PF and FlarmView, ymmv.

-Dave

On Sat, 07 May 2016 12:07:19 -0700, Darryl Ramm wrote:

So do you have much traffic below ~2,000' AGL where you are? That are
also in SSR interrogator coverage? (although TCAS should fill in as an
interrogator). Why not try setting everything unlimited and see what
happens.

Partial obstructions, local reflections etc. can severely screw with
PCAS's estimation of range. Testing that on the ground may be a waste of
time.

On Saturday, May 7, 2016 at 11:44:51 AM UTC-7, David Kinsell wrote:
Currently using the default flarmcfg.txt file, so 7000 and 600.


Sat, 07 May 2016 10:13:05 -0700, Darryl Ramm wrote:

And what are your PowerFLARM's PCAS range and altitude settings set
to?

On Saturday, May 7, 2016 at 7:11:29 AM UTC-7, David Kinsell wrote:
On Thu, 05 May 2016 11:50:39 -0700, Richard wrote:

On Thursday, May 5, 2016 at 11:17:11 AM UTC-7,
wrote:
Here at Chicago Glider Club we have the dubious distinction of
flying right under the approach path into Midway airport. I have
looked at SouthWest planes coming through from all angles,
including head-on. Flying with a C-mode transponder helps a lot,
Approach will guide the big iron around us although I'm sometimes
wondering about the spacing. My PFlarm will indicate through the
FlarmView display a blue dot around my position that is blinking
ONLY when a SW or bigger commercial plane (equipped with TCAS?)
is coming through. Could there be a connection such that the
transponder when interrogated by a TCAS responds in a way that is
picked up by PFlarm? What else might the blue blinking dot mean?
Please enlighten me.
Herb, J7

that is a mode C or mode S transponder it is non directional and
as it gets closer the circle should get smaller. Blue means it is
above you.

Richard www.craggyaero.com

I've been bench testing 6.06 firmware, and see what I believe Herb
is seeing. A small flashing dot right at current position, but it's
short lived and never gets bigger. It's like the range for mode
c/mode s targets is terrible. I see lots of ADS-B targets at
distances greater than 12 miles, but hardly any mode c/mode s.
Maybe they gave up trying to estimate distance for those targets?

On Saturday, May 7, 2016 at 10:11:29 AM UTC-4, David Kinsell wrote:
On Thu, 05 May 2016 11:50:39 -0700, Richard wrote:

On Thursday, May 5, 2016 at 11:17:11 AM UTC-7, wrote:
Here at Chicago Glider Club we have the dubious distinction of flying
right under the approach path into Midway airport. I have looked at
SouthWest planes coming through from all angles, including head-on.
Flying with a C-mode transponder helps a lot, Approach will guide the
big iron around us although I'm sometimes wondering about the spacing.
My PFlarm will indicate through the FlarmView display a blue dot around
my position that is blinking ONLY when a SW or bigger commercial plane
(equipped with TCAS?) is coming through. Could there be a connection
such that the transponder when interrogated by a TCAS responds in a way
that is picked up by PFlarm? What else might the blue blinking dot
mean?
Please enlighten me.
Herb, J7

that is a mode C or mode S transponder it is non directional and as it
gets closer the circle should get smaller. Blue means it is above you.

Richard www.craggyaero.com

I've been bench testing 6.06 firmware, and see what I believe Herb is
seeing. A small flashing dot right at current position, but it's short
lived and never gets bigger. It's like the range for mode c/mode s
targets is terrible. I see lots of ADS-B targets at distances greater
than 12 miles, but hardly any mode c/mode s. Maybe they gave up trying
to estimate distance for those targets?

IIRC PF's max (software limited) range for non-directional "traffic" is 6 miles. It's in their docs, somewhere.

Why would you want flarm to report non-directional "traffic" beyond even 3 miles? Nice to know your device is working I suppose, but in flight this is just another distraction.

Suggest you set the range of your display to something useful like 2 - 4 miles. Set to 24 miles, which is what I guess is going on here, the important stuff (the close stuff) will not be displayed properly (e.g. blinking dots).

best,
Evan Ludeman