If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Tail dolly for 1-35?
Hello all - I've decided that I need to build a tail dolly for my 1-35. It occurs to me that maybe someone has one they'd sell and that would save me the trouble...? One from a 1-34 would likely also fit...
|
#2
|
|||
|
|||
Tail dolly for 1-35?
Hi,
Is there any chance that the tail dolly shown in the link below is for a 1-35? https://www.facebook.com/media/set/?...07162& type=3 Best Regards, Paul Remde _____________________________ wrote in message ... Hello all - I've decided that I need to build a tail dolly for my 1-35. It occurs to me that maybe someone has one they'd sell and that would save me the trouble...? One from a 1-34 would likely also fit... |
#3
|
|||
|
|||
Tail dolly for 1-35?
On Saturday, September 21, 2013 1:53:38 PM UTC-4, wrote:
Hello all - I've decided that I need to build a tail dolly for my 1-35. It occurs to me that maybe someone has one they'd sell and that would save me the trouble...? One from a 1-34 would likely also fit... Dear Paul - could be? My ship is about 200 miles away, may see in a few days. I know that the width of the fuselage right about the front of the vertical stab is 7.25" - let me know if that's a match, and the height of the cross-section at that point on your dolly...and what you'd want for it. Reply in private if you like. |
#4
|
|||
|
|||
Tail dolly for 1-35?
On Saturday, September 21, 2013 1:53:38 PM UTC-4, wrote:
Hello all - I've decided that I need to build a tail dolly for my 1-35. It occurs to me that maybe someone has one they'd sell and that would save me the trouble...? One from a 1-34 would likely also fit... My club has a 1-35 tail dolly/wheel that has been languishing at the club since the owner wrecked his 1-35 years ago and donated the carcass to the club. Let me take a couple of pics if it is still around and see if the BoD will sell it. Actually not doing us any good. but, I'm not on the BoD. as I remember, this tail dolly lock onto the tail wheel spring. r/Jim |
#5
|
|||
|
|||
Tail dolly for 1-35?
You can find a photo of the tail dolly that I made for my 1-35 on the 1-35 website. It looks very similar to the mystery dolly referred to by Paul Remde.
Raul Boerner http://members.goldengate.net/~tmren...il%20dolly.JPG |
#6
|
|||
|
|||
Tail dolly for 1-35?
On Saturday, September 21, 2013 1:53:38 PM UTC-4, wrote:
Hello all - I've decided that I need to build a tail dolly for my 1-35. It occurs to me that maybe someone has one they'd sell and that would save me the trouble...? One from a 1-34 would likely also fit... Thanks, everyone - especially Paul Remde! His mystery hangar flotsam turned out to be a perfect fit, and quite clean and well-made. What service! |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
LS4 tail dolly | Leigh | Soaring | 0 | May 30th 08 02:02 AM |
ASK-21 - is a tail dolly necessary? | Dave Springford | Soaring | 7 | December 31st 07 08:43 AM |
FS: ASW-24 Tail Dolly | [email protected] | Soaring | 0 | December 26th 06 02:40 PM |
WTB: used tail dolly | David Campbell | Soaring | 5 | April 17th 06 03:19 PM |
L-23 tail dolly | Mark Zivley | Soaring | 1 | November 27th 04 11:16 AM |