A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » General Aviation
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

GIF of plane hit by lightning



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #4  
Old June 3rd 04, 04:43 AM
Jim Knoyle
external usenet poster
 
Posts: n/a
Default


"MikeM" wrote in message
...
Dan Jacobson wrote:

GIF of plane hit by lightning:
http://bm6aak.myweb.hinet.net/file/456.gif
(Lightning hits planes everyday and is no big deal.)


What it clearly shows is that airplanes do not get "hit
by lightning". What actually happens is that a lightning
bolt already headed from ground to cloud sometimes
makes a small detour through a conductive object (airplane)
if it happens to be where the lightening bolt may have gone
anyway.

There are billions of volts cloud-to-ground before the strike.
Once the air in the lightning bolt path is ionized, the
current that flows is only a few thousand Amps.
A metallic aircraft, if it becomes part of the current path,
has a max voltage drop across it of only a few hundred volts.

The airplane is self-protected in the same way as installing
a #8awg copper wire from a "lightening rod" from the roof of
a barn, around the outside of the barn, to a ground rod.
During a strike, the potential from tip of the lightening
rod to the ground under the barn is constrained to a few
hundred volts... This keeps the destructive current path out
of the wood; it flows along the copper wire instead of in the
wood.

Dont try this with a plastic, composite or wood aircraft.
The current pulse instantly turns absorbed moisture into steam,
literally blowing the aircraft apart.


Some occasional exceptions. One DC-10 I worked
had a real interesting bit of artwork after a strike. Along
the left side there was a splotch about three feet long as
if some artist had painted a jagged line with his paintbrush.
On closer exam, the splotch consisted of pitted and melted
aluminum.
Back when the Weather Radar (AVQ 10/30) used a parabolic
dish for a scanner, the scanner bearings could get welded solid.
The scanner probe consisted of an approx. 4 inch long 1/4 inch
diameter alloy rod for a probe. This rod was encapsulated into
a solid 3/4 inch Teflon cylinder. After a strike this Teflon could
look like a bit of Swiss cheese or a bad case of termites.

JK


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
rec.aviation.aerobatics FAQ Dr. Guenther Eichhorn Aerobatics 0 September 1st 04 08:27 AM
rec.aviation.aerobatics FAQ Dr. Guenther Eichhorn Aerobatics 0 December 1st 03 07:27 AM
Conspiracy Theorists (amusing) Grantland Military Aviation 1 October 2nd 03 01:17 AM
A Good Story Badwater Bill Home Built 15 September 3rd 03 04:00 PM
rec.aviation.aerobatics FAQ Dr. Guenther Eichhorn Aerobatics 0 September 1st 03 08:27 AM


All times are GMT +1. The time now is 12:35 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 AviationBanter.
The comments are property of their posters.