A aviation & planes forum. AviationBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » AviationBanter forum » rec.aviation newsgroups » Owning
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

1976 Overhaul, 1100 Hours..Pass???/



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #28  
Old September 14th 05, 01:45 AM
Mike Spera
external usenet poster
 
Posts: n/a
Default

Exactly why I offered the advice that I did. Namely, pulling a cylinder
is not what most think of as a "normal" prebuy operation. Also, the
suggestion may get a "smart" reply or outright laugh.

I agree that pulling one jug gives you a limited view. What are you
looking for? Well, how about a lobe that is ground off 30-50%? for
starters. If you catch a copy of Light Plane Maintenance, they have an
easier way to determine this on all the lobes by dial gauging the backs
of the tappets. Still requires some disassembly, but nowhere near as
radical as pulling a jug. Please don't mix up the pushrods.

Since Lycomings may run fine with a lobe seriously ground off, this may
be a better alternative.

Above all, as I said, chances are that any "unusual" requests (like
these) beyond the normal "once over lightly pre-buy" will likely be
rejected.

Sarcasm and anger noted below, although I'm not sure what I said to
provoke it.

Good Luck,
Mike


OK, let's say that you pull a jug for "inspection". Exactly what do you
expect to find by this? Where is this "rust" going to be? At BEST you will
see four camshaft lobes. That isn't going to tell you squat except for
those four lobes. If the engine has been run recently, all the splash hot
oil will have removed any rust particles you have a chance of seeing.

Now you've pulled the jug. New rings, a hone job on the cylinder, new
cylinder gasket kit, change oil to breakin oil, and for what? And who is
going to pay for it? Lemme TELL you who is going to pay for it, buy the
airplane or not. And if the airplane doesn't break in properly within a
couple of dozen hours, guess who gets to pay for the REdo. You do, redo and
all.

Airplanes are best sold on the "this is the price, no matter what your
mechanic finds" basis. You find some stuff that doesn't make you want to
buy, that's fine. No problem. See ya later.

J



"Mike Spera" wrote in message
link.net...


. Others also balked about pulling

a jug for a prebuy. Normally, it is true that this is not done. There are
plenty of uninformed buyers with enough credit to buy a bird uninspected
and sight unseen. So, an unusual request like pulling a jug will no doubt
get you a firm "No F^@%!*G Way" of some kind of robust belly laugh.




 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
AOPA Stall/Spin Study -- Stowell's Review (8,000 words) Rich Stowell Aerobatics 28 January 2nd 09 03:26 PM
"I Want To FLY!"-(Youth) My store to raise funds for flying lessons Curtl33 General Aviation 7 January 10th 04 12:35 AM
Real stats on engine failures? Captain Wubba Piloting 127 December 8th 03 05:09 PM
AmeriFlight Crash C J Campbell Piloting 5 December 1st 03 03:13 PM
AOPA Stall/Spin Study -- Stowell's Review (8,000 words) Rich Stowell Piloting 25 September 11th 03 02:27 PM


All times are GMT +1. The time now is 04:45 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 AviationBanter.
The comments are property of their posters.