control cable questions

If it was my plane I'd throw the cable away and start over. Hiding the
2 broken strands under a new nico is a bad idea but adding a splice or
turnbuckle would work. Cable is cheap though so why not just change
the whole thing. As screw ups go that's only a little one.

On Wed, 07 May 2008 10:47:59 GMT, "Dick" wrote:

we were able to dremel down the center between the two cable segments but
removing the halfs apparently caused the damage.

Hope someone has some advise as the Bingelis books don't address repairs...

thanks
"Tim Ward" wrote in message
...

"Dick" wrote in message
news:g06Uj.5548$0L.5089@trnddc07...
Having to reject the last nicropress
on the rudder, two strands were cut when the nircopress was cut off with
a
drmel tool.

The question is whether we can reinstall a nicropress in the original
position and then add one an 1/8" further?? or,

Make splice two lengths of control cable with double nicropresses?? or,


Is there any reason why a turnbuckle couldn't be used ouitside the
fuselage
at the rudder??

Thanks



A big pair of end nippers is a very useful tool when you need to remove
nicopress sleeves. Too late now, of course.

Tim Ward

agreed, no hiding strands. however with all three of us big, heavy, stiff
guys, we can't get inside the fuselage G
"Drew Dalgleish" wrote in message
...
If it was my plane I'd throw the cable away and start over. Hiding the
2 broken strands under a new nico is a bad idea but adding a splice or
turnbuckle would work. Cable is cheap though so why not just change
the whole thing. As screw ups go that's only a little one.

On Wed, 07 May 2008 10:47:59 GMT, "Dick" wrote:

we were able to dremel down the center between the two cable segments but
removing the halfs apparently caused the damage.

Hope someone has some advise as the Bingelis books don't address
repairs...

thanks
"Tim Ward" wrote in message
...

"Dick" wrote in message
news:g06Uj.5548$0L.5089@trnddc07...
Having to reject the last nicropress
on the rudder, two strands were cut when the nircopress was cut off
with
a
drmel tool.

The question is whether we can reinstall a nicropress in the original
position and then add one an 1/8" further?? or,

Make splice two lengths of control cable with double nicropresses?? or,


Is there any reason why a turnbuckle couldn't be used ouitside the
fuselage
at the rudder??

Thanks



A big pair of end nippers is a very useful tool when you need to remove
nicopress sleeves. Too late now, of course.

Tim Ward

On 2008-05-07, Dick wrote:
agreed, no hiding strands. however with all three of us big, heavy, stiff
guys, we can't get inside the fuselage G

Can you use the old cable as a fish tape to pull the new cable through?
--
Jay Maynard, K5ZC http://www.conmicro.com
http://jmaynard.livejournal.com http://www.tronguy.net
Fairmont, MN (FRM) (Yes, that's me!)
AMD Zodiac CH601XLi N55ZC (ordered 17 March, delivery 2 June)

possibly but last time I tried a few years ago but still fat G, my taped
connection came loose. now that I just wrote that maybe an electrical wire
butt splice would work. thanks for stimulation.
"Jay Maynard" wrote in message
...
On 2008-05-07, Dick wrote:
agreed, no hiding strands. however with all three of us big, heavy, stiff
guys, we can't get inside the fuselage G

Can you use the old cable as a fish tape to pull the new cable through?
--
Jay Maynard, K5ZC http://www.conmicro.com
http://jmaynard.livejournal.com http://www.tronguy.net
Fairmont, MN (FRM) (Yes, that's me!)
AMD Zodiac CH601XLi N55ZC (ordered 17 March, delivery 2 June)